跳转到主内容

修复你的物品

维修的权力

配件 & 工具

视频概述

  1. Remove back cover. Moto G3 plastic panel can be easily removed with the fingernails.
    • Remove back cover.

    • Moto G3 plastic panel can be easily removed with the fingernails.

  2. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.
    • Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.

  3. Undo 3 screws by T4 Torx screwdriver. Take away plastic securing part.
    • Undo 3 screws by T4 Torx screwdriver.

    • Take away plastic securing part.

  4. Heat up the LCD screen for a while. Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives. There is LCD screen connector on the left side, so be careful to slide guitar picks.
    • Heat up the LCD screen for a while.

    • Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives.

    • There is LCD screen connector on the left side, so be careful to slide guitar picks.

  5. Release LCD screen connector firstly. Remove LCD screen. Remove LCD screen.
    • Release LCD screen connector firstly.

    • Remove LCD screen.

  6. Undo 14 screws by T4 Torx screwdriver Pry up motherboard assembly. Battery flex connector is connected with motherboard, so be careful to pry the assembly up.
    • Undo 14 screws by T4 Torx screwdriver

    • Pry up motherboard assembly.

    • Battery flex connector is connected with motherboard, so be careful to pry the assembly up.

  7. 任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装

    任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装
  8. Release battery flex connector. Separate motherboard assembly from back cover assembly.
    • Release battery flex connector.

    • Separate motherboard assembly from back cover assembly.

  9. Undo 3 screws here. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.
    • Undo 3 screws here.

    • Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.

  10. Remove front-facing camera. Remove front-facing camera.
    • Remove front-facing camera.

  11. Remove rear camera. Remove rear camera. Remove rear camera.
    • Remove rear camera.

  12. Remove earpiece. Remove earpiece.
    • Remove earpiece.

  13. Remove loudspeaker. Remove loudspeaker.
    • Remove loudspeaker.

  14. Here is the motherboard. Here is the motherboard.
    • Here is the motherboard.

  15. Use spudger to cut adhesive and pry the battery up. Use spudger to cut adhesive and pry the battery up.
    • Use spudger to cut adhesive and pry the battery up.

  16. Take away headphone jack. Take away headphone jack. Take away headphone jack.
    • Take away headphone jack.

  17. Done
    • Done

终点

15等其他人完成本指南。

Witrigs

于2015年11月24日注册

64,756 信誉积分

创作了386篇指南

Muito bom, parabéns!

Manoel - 回复

Could you guys tell me if the main speaker, at the bottom, has a special protection agains water spills, like a membrane or so, or is it pretty fine too spill water there?

setsuoleandro - 回复

Wi fi not trun on ..moto g3

Seoni Seoni - 回复

When you heat up the display, do you heat up the entire display or just around the edges? What heat gun/setting should i use? Can i use a blowdryer?

guest - 回复

Thanks. ......................

Biswajit Saha - 回复

添加评论

浏览统计数据:

过去的24小时: 16

过去的7天: 45

过去的30天: 185

总计 20,175