iOpener

  • iOpener / Toolkit / New
  • iOpener / Tool Only / New
  • iOpener / Tool Only / New
  • 360°
360
iOpener

This product cannot be shipped to Mexico.

Este producto no puede enviarse a México.

$19.99

$19.99

当产品有货时,我们将给你发送消息。

产品详细说明

描述

描述

The iOpener is a tablet opening tool designed to apply heat directly and evenly to case components joined with adhesive. Once the adhesive is softened with heat applied by the iOpener, the adhesive can be sliced using the many tools included in the iOpener kit. This toolkit is designed specifically for the iPad, but works with all tablets, smartphones, or other electronics needing heat application in the disassembly process. The iOpener is heated in your microwave. It is reusable, non-toxic, and food safe.

备注

This product cannot be shipped to Mexico.

免责声明

Avoid overheating your iOpener, follow this handy microwave heating guide.

维修的故事

ericzel08's Story Photo #1329847
ericzel08's Story Photo #1329848

我的问题

Phone was dropped. Screen cracked so bad there was no display.

我的修理方法

As good as most screen repairs can be expected to go.

我的建议

Buy some adhesive tape. If I had some I would've completely removed the leftover junk and put new stuff on the screen.

我的问题

I waited like 8 months for parts to come into stock. Poor inventory procurement!

我的修理方法

Series 2 - 42mm screen and digizer installed as expected.

我的建议

Take your time. Use a small 1mm flat head screw driver to remove the extra 3M double sided tape from the aluminum sealing surface. Use acitone to remove the extra . . .

我的问题

The housing on my Switch had become warped, in ordered a replacement housing and decided to throw some custom colors on my Joy-Cons while I was at it.

我的修理方法

Fairly easy, the hardest part was making sure not to tear the digitizer flex and making sure all the meshes small parts were transferred from the old . . .

我的问题

Went well. He did all the work and I just held the laptop and scroll down the instructions. He is 14 y.o. and has done multiple screen replacements and battery replacements.

我的修理方法

See above.

我的建议

Perfect Father & Son bonding experience.

我的问题

Lithium battery needed to be replaced

我的修理方法

Your instructions were spot on and the repair was perfect.

我的建议

Patience and heat to loosen the adhesive.

我的问题

My wife dropped it several times creating multiple cracks on the screen.

我的修理方法

The repair went well. I took my time and followed all the steps in the repair guide faithfully. I was even able to unsolder the small wake/sleep sensor from the broken screen and microsolder it back onto the new replacement scre . . .

我的问题

My pixel XL's USB-C port would smoke when the cable was connected and the plastic portion of the connection was visibly melted.

我的修理方法

I was successful in changing the battery charging circuit/daughter board but I accidentally sliced the digitizer traces on the ribbon cable for the OLED panel while removing . . .

我的问题

My phone is long since out of warranty or support. The battery had gotten to a point where I needed to charge as I used for traffic app, etc. I watched the videos and decided it was well within my capabilities to change battery. Worst case scenario would be that I irretrievably broke something and . . .

我的问题

After well over 2 years in service, my factory battery was completely incapable of powering the phone for more than a few minutes with the screen off. Turning the screen on meant a nearly instant shutdown.

我的修理方法

The repair went incredibly well. Despite this being a particularly difficult phone to open, i . . .

我的问题

The battery was losing charge rapidly, and seemed to be showing its age. The Pixels that have come out since did not appear to be compelling upgrades. So, I figured replacing the battery made the most sense.

我的修理方法

The outcome was positive. Opening the phone requires getting past a lot of epoxy. I marred on . . .

显示更多