跳转到主内容

修复你的物品

维修的权力

配件 & 工具

注:你正在为你刚才查阅的指南编辑前提条件。你所做的任何更改将影响包括此步骤的2本指南

英语
中文

正翻译步骤 15

步骤 15
Remove the battery. Before installing your new battery, remove all the old adhesive from the MacBook Pro's case.
  • Remove the battery.

  • Before installing your new battery, remove all the old adhesive from the MacBook Pro's case.

  • With a little luck, you can slowly pull out each strip of adhesive with your fingers.

  • Otherwise, soak each section of adhesive with a bit of adhesive remover for 2-3 minutes, and then scrape it out with an opening pick or one of the other tools in your kit. This can take quite a bit of work, so be patient.

  • Mop up any remaining adhesive remover and give your MacBook Pro a few minutes to air dry.

  • The replacement battery included in your iFixit kit comes with adhesive pre-installed. Test the battery's fit and alignment carefully before peeling off the film covering the adhesive, and then press each cell firmly into place. If any additional films/liners are present that weren't on your original battery, remove them last.

  • Calibrate your newly installed battery: charge it to 100%, and keep charging it for at least 2 more hours. Unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

  • If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook Pro's SMC.

移除电池。

在安装新的电池前,从MacBook Pro壳子中移除所有残留的粘合剂。

幸运的话,你可以用你的手慢慢地将粘合剂撕下来。

否则,用一点粘合剂去除剂将每个粘合剂部分浸泡2-3分钟,然后用撬片或其他工具将其刮掉。 这可能需要相当多的工作,所以要耐心。

擦拭残留的粘合剂去除剂,花一些时间让MacBook Pro风干。

iFixit套件中的更换电池已预先安装了粘合剂。 在剥离覆盖胶粘剂的胶片之前,仔细确保电池的对位,然后将每个电池牢固地按入到位。如果更换电池上有原电池上不存在的胶片、衬垫,请将它们移除。

校正 您新安装的电池: 充电至100%, 并保持充电状态至少2小时。拔掉电源并使用电池供电。当您看到低电量警告时,保存您的工作,继续使用您的笔记本直到低电量自动睡眠。静置5小时后一次将电量充至100%。

如果您在安装新电池后发现任何不寻常的行为或问题,可能需要重置MacBook Pro的SMC。

[* black] Remove the battery.
[* icon_reminder] Before installing your new battery, remove all the old adhesive from the MacBook Pro's case.
[* black] With a little luck, you can slowly pull out each strip of adhesive with your fingers.
[* black] Otherwise, soak each section of adhesive with a bit of adhesive remover for 2-3 minutes, and then scrape it out with an opening pick or one of the other tools in your kit. This can take quite a bit of work, so be patient.
[* black] Mop up any remaining adhesive remover and give your MacBook Pro a few minutes to air dry.
[* icon_reminder] The replacement battery included in your iFixit kit comes with adhesive pre-installed. Test the battery's fit and alignment carefully before peeling off the film covering the adhesive, and then press each cell firmly into place. If any additional films/liners are present that weren't on your original battery, remove them nowlast.
[* icon_reminder] The replacement battery included in your iFixit kit comes with adhesive pre-installed. Test the battery's fit and alignment carefully before peeling off the film covering the adhesive, and then press each cell firmly into place. If any additional films/liners are present that weren't on your original battery, remove them nowlast.
[* black] [[Battery Calibration|Calibrate]] your newly installed battery: charge it to 100%, and keep charging it for at least 2 more hours. Unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
[* black] If you notice any unusual behavior or problems after installing your new battery, you may need to [https://support.apple.com/en-gb/HT201295|reset your MacBook Pro's SMC|new_window=true].

在开源创作共享许可协议下,你的投稿已被许可