跳转到主内容

注:你正在为你刚才查阅的指南编辑前提条件。你所做的任何更改将影响包括此步骤的4本指南

英语
中文

正翻译步骤 7

步骤 7
To install a new back cover: Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
  • To install a new back cover:

  • Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.

  • Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.

  • If you're reinstalling the old back cover, or using a back cover without adhesive pre-installed, follow this guide.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

重装后壳:

首先用镊子揭掉后盖和手机后框上残留的胶。

然后,用高浓度(至少90%)异丙醇和不起毛的布来清理粘胶的部位。擦的时候只向一个方向擦,不要来回来去地擦。这能让表面更适合新的胶来粘合。

在重新封合你的手机前要开机确保你的维修成功了。

为了适合后壳的轮廓,替换胶应是放在一个预裁好的纸上的。如果没有那种胶,你也可以用一种高粘着力的双面胶,如Tesa 61395。但你要知道这样的粘合会留有能透液体的缝隙。

在安完后盖之后,在手机上施加强劲稳定的压力几分钟来帮助胶形成好的附着,你可以把手机放在一摞书下面。

如果你想的话,你也可以用旧有的胶粘回后盖。去掉可能会妨碍后盖整齐粘回原位的大块胶。在安装完成后,加热后盖然后加压来让后盖粘牢。这样不会防水,但是胶一般会足够牢固。

[* icon_reminder] To reinstall theinstall a new back cover:
[* black] First useUse tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.
[* black] Then,
Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will helpcloth to prep the surface for the new adhesive.
[* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
[* icon_reminder] If you're reinstalling the old back cover, or using a back cover without adhesive pre-installed, [guide|124003|follow this guide|new_window=true].
[* icon_note]
Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as [product|IF317-072|Tesa 61395|new_window=true]. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
[* black] After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
[* icon_reminder] To reinstall theinstall a new back cover:
[* black] First useUse tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.
[* black] Then,
Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will helpcloth to prep the surface for the new adhesive.
[* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
[* icon_reminder] If you're reinstalling the old back cover, or using a back cover without adhesive pre-installed, [guide|124003|follow this guide|new_window=true].
[* icon_note]
Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as [product|IF317-072|Tesa 61395|new_window=true]. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
[* black] After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

在开源创作共享许可协议下,你的投稿已被许可