跳转到主内容

修复你的物品

维修的权力

配件 & 工具

简介

If the nozzle of your Braava Jet 240 is faulty, use this guide to replace it. You will only need a Phillips #1 screwdriver.

The nozzle is used to spray water onto the ground for the robot to mop up. Sometimes debris can get into the nozzle and cause it to spray in an abnormal pattern, or not at all. If this happens, it will need to be replaced.

  1. Turn the device off.
    • Turn the device off.

  2. Use your fingers to gently pop out the battery. Use your fingers to gently pop out the battery.
    • Use your fingers to gently pop out the battery.

  3. Lift up the handle to reveal the eject button. Lift up the handle to reveal the eject button.
    • Lift up the handle to reveal the eject button.

  4. Use your finger to push the eject button forward. Use your finger to push the eject button forward. Use your finger to push the eject button forward.
    • Use your finger to push the eject button forward.

  5. 任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装

    任天堂 Switch 套装

    快速恢复到游戏的状态

    购买 Switch 套装
  6. Tilt the robot on its side and let the mop pad slide out.
    • Tilt the robot on its side and let the mop pad slide out.

  7. Remove the two 22.0  mm screws on the bottom-front of the robot using a Phillips #1 screwdriver. Remove the two 22.0  mm screws on the bottom-front of the robot using a Phillips #1 screwdriver.
    • Remove the two 22.0 mm screws on the bottom-front of the robot using a Phillips #1 screwdriver.

  8. Use a Phillips #1 screwdriver and an iFixit opening tool to remove the two 15.0 mm screws on the front sides of the robot. Use a Phillips #1 screwdriver and an iFixit opening tool to remove the two 15.0 mm screws on the front sides of the robot.
    • Use a Phillips #1 screwdriver and an iFixit opening tool to remove the two 15.0 mm screws on the front sides of the robot.

  9. Carefully pull back on the front shell to remove it from the robot. Carefully pull back on the front shell to remove it from the robot. Carefully pull back on the front shell to remove it from the robot.
    • Carefully pull back on the front shell to remove it from the robot.

  10. Pull the nozzle assembly away from the body of the robot. Pull the nozzle assembly away from the body of the robot.
    • Pull the nozzle assembly away from the body of the robot.

  11. Using a Phillips #1 screwdriver, remove the 16 mm screw that holds the nozzle in place. Using a Phillips #1 screwdriver, remove the 16 mm screw that holds the nozzle in place. Using a Phillips #1 screwdriver, remove the 16 mm screw that holds the nozzle in place.
    • Using a Phillips #1 screwdriver, remove the 16 mm screw that holds the nozzle in place.

  12. Continue unscrewing the 16 mm screw until it comes out of the nozzle.
    • Continue unscrewing the 16 mm screw until it comes out of the nozzle.

  13. Gently remove the tube from the nozzle. Gently remove the tube from the nozzle. Gently remove the tube from the nozzle.
    • Gently remove the tube from the nozzle.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Claire Franz

于2020年02月10日注册

790 信誉积分

创作了7篇指南

团队

iFixit iFixit 的会员

Community

123 名成员

创作了11,548篇指南

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 9

过去的30天: 105

总计 287