跳转到主内容
  1. 打開 iPod 之前,請確保保持開關處於鎖定位置。 橙色條應該可見,表示保持處於活動狀態。
    • 打開 iPod 之前,請確保保持開關處於鎖定位置。 橙色條應該可見,表示保持處於活動狀態。

  2. 將三角撬片盡可能插入 iPod 右側邊緣的塑料前面板和金屬後面板之間的接縫中。 您可能需要前後搖動撥片才能將其滑入更遠。 使用三角撬片撬起塑料前面板並釋放五個固定片(見第三張照片)。
    • 將三角撬片盡可能插入 iPod 右側邊緣的塑料前面板和金屬後面板之間的接縫中。

    • 您可能需要前後搖動撥片才能將其滑入更遠。

    • 使用三角撬片撬起塑料前面板並釋放五個固定片(見第三張照片)。

    • 沿著 iPod 的邊緣滑動撬片並繼續撬動以釋放其餘的固定片。

    • 在右側的所有五個標籤都空閒後,外殼應該很容易打開。

  3. iPod 外殼現已打開,但暫時不要將兩半分開。 仍然有一條橙色的帶狀電纜將耳機插孔連接到邏輯板。
    • iPod 外殼現已打開,但暫時不要將兩半分開。 仍然有一條橙色的帶狀電纜將耳機插孔連接到邏輯板。

    • 像書本一樣打開外殼,底座連接器邊緣位於頂部,然後將後面板放在 iPod 前半部分旁邊。

  4. 使用塑料工具或指甲小心地斷開橙色耳機插孔電纜。 確保將連接器向上拉直,而不是電纜本身。
    • 使用塑料工具或指甲小心地斷開橙色耳機插孔電纜。 確保將連接器向上拉直,而不是電纜本身。

    • 這種帶狀電纜非常脆弱。 如果要更換電池,可以選擇跳過此步驟,保持耳機插孔與主板連接。 將後殼支撐並用膠帶固定在盒子上以將其固定到位。 工作時要非常小心,不要拉傷易碎的耳機插孔電纜。

  5. 这个步骤还没有翻译 帮忙翻译一下

    Grasp the hard drive with one hand and carefully disconnect the orange ribbon cable from the hard drive using your other hand.
    • Grasp the hard drive with one hand and carefully disconnect the orange ribbon cable from the hard drive using your other hand.

    • If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.

  6. 这个步骤还没有翻译 帮忙翻译一下

    Peel up the black adhesive strip covering the hard drive ribbon cable.
    • Peel up the black adhesive strip covering the hard drive ribbon cable.

  7. 这个步骤还没有翻译 帮忙翻译一下

    Use the tip of your finger or a spudger to carefully flip up the black connector securing the hard drive cable to the logic board.  Note that the black retaining clip flips 90 degrees toward vertical, in the direction of the cable.
    • Use the tip of your finger or a spudger to carefully flip up the black connector securing the hard drive cable to the logic board. Note that the black retaining clip flips 90 degrees toward vertical, in the direction of the cable.

  8. 这个步骤还没有翻译 帮忙翻译一下

    Pull the orange hard drive cable directly out of its connector.
    • Pull the orange hard drive cable directly out of its connector.

  9. 这个步骤还没有翻译 帮忙翻译一下

    Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.
    • Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

  10. 这个步骤还没有翻译 帮忙翻译一下

    Use a spudger to flip up the black retaining bars securing the display and click wheel connectors to the logic board.
    • Use a spudger to flip up the black retaining bars securing the display and click wheel connectors to the logic board.

    • If you have an iPod Photo, the display connector (to the right of the picture) is located more centrally on the logic board.

  11. 这个步骤还没有翻译 帮忙翻译一下

    Remove the 6 black T6 Torx screws securing the logic board to the front panel.
    • Remove the 6 black T6 Torx screws securing the logic board to the front panel.

    • If you have an iPod Photo, there will only be 5 screws, as there is no screw in the top right corner of the iPod.

  12. 这个步骤还没有翻译 帮忙翻译一下

    Slide the orange click wheel ribbon cable out of its connector.  You must unlock this connector before sliding the ribbon cable out. The locking mechanism is on the opposite side of where the cable is inserted - it swivels upwards 90 degrees. Use a plastic spudger to lift the locking mechanism.
    • Slide the orange click wheel ribbon cable out of its connector. You must unlock this connector before sliding the ribbon cable out. The locking mechanism is on the opposite side of where the cable is inserted - it swivels upwards 90 degrees. Use a plastic spudger to lift the locking mechanism.

  13. 这个步骤还没有翻译 帮忙翻译一下

    Carefully lift up the large end of the logic board and disconnect the display connector.
    • Carefully lift up the large end of the logic board and disconnect the display connector.

    • Lift the logic board out of the iPod.

终点

27等其他人完成本指南。

iRobot

于2009年09月24日注册

1 信誉积分

创作了646篇指南

3条评论

what's the differece between 20G logic board and 40G logic board? I have changed hard drive into CF card and now I have to change logic board..

mulddae - 回复

So there’s the difference between 20gb and 40gb logic board? I’ve changed 20gb HDD to new 40gb HDD and now Can't get to work my ipod! So what to do?

EVGENY BRENER -

No idea if anyone will respond to this but here goes: Okay so I just want to know if you can repair the part where you attach the screen cable to the logic board, that part suddenly came off and was wondering if there’s a way to reattach that part back onto the logic board so the display can show up??

hgabriel_93 - 回复

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 23

过去的30天: 126

总计 39,488