跳转到主内容

iPhone 7 Power and Volume Control Cable Battery Replacement

仅作为前提条件
本指南仅用作其他指南的先决条件。不能单独食用。

你所需要的

  1. iPhone 7 Power and Volume Control Cable Battery Replacement, Power and Volume Control Cable Battery: 步骤 1 中的图像 1,2 iPhone 7 Power and Volume Control Cable Battery Replacement, Power and Volume Control Cable Battery: 步骤 1 中的图像 2,2
    • Use the flat end of a spudger to disconnect the Taptic Engine connector from its socket on the logic board.

  2. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 2 中的图像 1,1
    • Remove the three 1.6 mm Phillips screws securing the Taptic Engine to the rear case.

  3. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 3 中的图像 1,2 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 3 中的图像 2,2
    • Remove the Taptic Engine.

  4. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 4 中的图像 1,3 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 4 中的图像 2,3 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 4 中的图像 3,3
    • Use a pair of tweezers with blunt tips to peel back one of the adhesive strips on the lower edge of the battery.

  5. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 5 中的图像 1,2 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 5 中的图像 2,2
    • Use a pair of tweezers with blunt tips to peel back the other adhesive strip on the lower edge of the battery.

  6. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 6 中的图像 1,3 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 6 中的图像 2,3 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 6 中的图像 3,3
    • Try to keep the strips flat and unwrinkled during this procedure; wrinkled strips will stick together and break instead of pulling out cleanly.

    • Slowly pull one battery adhesive tab away from the battery, toward the bottom of the iPhone.

    • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at a 60º angle or less.

    • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

  7. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 7 中的图像 1,1
    • Repeat the previous step for the second strip.

    • Hold down the battery as you remove the second strip, or the strip may fling the battery when it separates from the case.

    • If you removed both adhesive strips successfully, skip the next step.

    • Otherwise, if either of the adhesive strips broke off underneath the battery and could not be retrieved, continue with the next step below.

  8. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 8 中的图像 1,2 iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 8 中的图像 2,2
    • If you successfully removed both adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear case.

    • Prepare an iOpener and apply it to the back of the rear case, directly over the battery. Alternatively, you can apply heat using a heat gun or hair dryer.

    • After about a minute, remove the iOpener, flip the phone over and use a plastic card to break up any remaining adhesive behind the battery.

    • Avoid bending the battery. Damage to the battery may release dangerous chemicals, and could start a fire.

    • Do not pry under the top third of the battery, you may damage the volume button ribbon cable.

  9. iPhone 7 Power and Volume Control Cable Battery Replacement: 步骤 9 中的图像 1,1
    • Remove the battery.

    • When installing the battery, refer to this guide to replace your battery's adhesive strips.

结论

To reassemble your device, follow these instructions in reverse order.

Scott Havard

于06/27/16注册

49,564 声望

创作了31篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 0

总计 136