1. 在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。
    • 在操作前我们推荐你清空微波炉,在底部的任何讨厌的食物残渣最终都可能粘在iOpener上。

    • 把iOpener放在微波炉中间 。

      • 对于旋转式微波炉:确保盘子可以自由旋转。如果你的iOpener卡住了,它可能会过热并燃烧

    which temperature must be used for heating? Thx

    fbarletta - 回复

    I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

    By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

    Fredrik -

    I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

    windizy - 回复

    I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

    Martin Gray - 回复

    I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

    Jan Van Puymbroeck - 回复

    Use a hair dryer! Watch this vid: https://youtu.be/16GkvjVyOJA It is much easier to do if you heat it from the other side.

    Fletcher Carpenter - 回复

    I wonder how many people actually wrapped in their iPhone into iOpener and put this "sandwich" into microwave??

    putinaspiliponis - 回复

    I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

    Laurie Higgins - 回复

    Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

    Yousef Ghalib - 回复

    I've been with Samsung for 8 years now!! Never did i have a case on any of my phones My Samsung 8 is 2 months old the case protector around the edge pop off and broke my phone it's like someone put a bullet hole in it

    Sherry Carew - 回复

    Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

    Esmond Pitt - 回复

    Hi, the microware have multiple power 1 to 9, what must be used ?



    Cedric VINCENT - 回复

  2. 加热iOpener三十秒
    • 加热iOpener三十秒

    • 贯穿整个维修过程,如果iOpener 冷却了,在微波炉中每次重新加热额外的三十秒。

    • 注意在维修过程中不要过度加热iOpener,过热可能会导致iOpener爆炸。

    • 如果出现膨胀千万不要碰iOpener。

    • 如果iOpener中间部分依然烫的没法碰,请等待冷却后再加热,一个加热好的iOpener 应该可以保持热度十分钟

    May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

    yamayhuang - 回复

    I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

    whale13 - 回复

    DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

    Alex Jackson - 回复

    I don't own a microwave.

    mdanihy - 回复

    Its again waterproof when you change iphone 7 battery?

    Jon - 回复

    I don't have a microwave???

    Joe Blow - 回复

    30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

    Sam Stieg - 回复

    can i use just ordinary microwave???

    juneseok kwon - 回复

    If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

    Mohideen Rifay - 回复

    I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

    Travis Dixon - 回复

    There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

    assortedrubbish - 回复

    I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

    dave - 回复

    If I may suggest include your microwave wattage so people can get an idea on time for there own

    Patrick Storey - 回复

    I ended up using a hair dryer. That iOpener thing took forever.

    mark fitzgerald - 回复

    30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

    60 seconds in the microwave, the iOpener burst.

    I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.


    Karl Marble - 回复

    • 把iOpener从微波炉中拿出来,捏着两边扁平边缘中的一个避免碰到中心热的部分。

    • iOpener会非常烫,所以拿着它的时候千万要小心。必要的时候可以使用烤箱手套。

    Will a hair dryer work for heating the glass?

    Me berg - 回复

    Yes, as does a heat gun.

    anonymous 4602 - 回复

    I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

    Cobus de Beer - 回复

    • 如果您的显示屏玻璃已经碎裂,防止显示屏玻璃在您维修时进一步伤害到您,请使用胶带来固定已经碎裂的屏幕。

    • 给iPad 的正面整面贴上胶带。

      • 这一步将保证在您翘起和移除显示屏时能够保持完整。

    • 尽量根据下面的指南进行操作。但,一旦玻璃破碎,请停下拆解并使用金属撬刀撬出玻璃,避免更多的碎裂。

    • 戴上安全眼镜来保护你的眼睛。 小心操作不要损坏了LCD内屏。

    In case of broken glass, here are some hints:

    - I prefer 3M "3350" tape; a metalized polypropylene tape with an acrylic adhesive. It's a very thin, silvery HVAC tape, not your standard duct tape.

    - Test your tape to make sure it sticks really well to the glass.

    - Use isopropyl alcohol on a paper towel to remove fingerprints and other dirt to help the tape stick to the screen.

    - Use the widest tape you can find, and apply it evenly, without trapping bubbles, without crinkles: This greatly improves your chance of success with the suction cup later.

    - Cut tape pieces long enough and go over the (rounded) edge; afterwards carefully run a scalpel alongside the edge (between bezel and glass) to trim off any excess.

    - Don't overlap edges of the tape: butt-join them instead.

    - If needed: repeat in other direction.

    - If needed: Cut square piece of tape (size of suction cup) and place it where you want to lift the glass, so that the suction cup doesn't cover any butt-joins.

    Good luck, you brave person!

    volty - 回复

    This is the second broken screen I’ve fixed. Overlapped package tape carefully stuck to the glass and trimmed to the edges will contain most of the shards. I found that a hair dryer works for softening the glue. After getting under an edge with the suction cup I carefully followed the opening sequence using a combination of plastic picks and a single edge razor blade to get under the small pieces. It was slow going with lots of reheating with the dryer (about 45 minutes), but the taped glass came off without glass everywhere.

    Bill Roughen - 回复

    • 将iOpener放置在iPad左侧。也就是Home键左侧位置。

    • 将iOpener放置至少5分钟来软化玻璃下面的粘合剂。

    I worked at it for over 2 hours before deciding to microwave the opener for 45 seconds at a time. That seemed to do the trick.

    jaromhyde - 回复

    • 将吸盘小心的放在刚加热的一侧中间的位置。

      • 确保吸盘已经牢牢吸住前玻璃面板。

    • 使用一只手在固定住iPad,另一只手慢慢提起吸盘,将前玻璃面板与后壳分离。

    • 小心将玻璃面板提起能够将撬棒插入的高度。 抬的过高玻璃会有破损的风险。

    This step is totally pointless if you have a shattered screen. The suction cup is rendered useless. Any tips on what to do if you can't get any suction due to a shattered screen?

    robloomis - 回复

    just pick out the glass shards if it is cracked that bad you are better off scrapping the digitizer

    Ethan Chow -

    for shattered screens I cover the screen with tape. I find packing tape works best for me.

    George - 回复

    • 拉住吸盘,在玻璃和机壳之间的缝隙处放置一个撬片。

      • 切勿将撬片插入深度超过黑色边框,这样深入过度可能会使LCD屏幕受损。

    • 然后拉动吸盘塑料部分来将吸盘从显示模组上取下。


    • 重新加热iOpener

      • 小心,请勿在维修过程中过度加热iOpener。 在重新加热iOpener之前请至少等待10分钟。

    • 将其放在ipad左侧几分钟来重新加热。


    • 沿着第一个撬片的开的口处插入另外一个翘片同时向下滑动,让撬片分离粘合剂。

    • 在下来的步骤中,如果您遇到了巨大的阻力,请停下来,重新加热工作的部位。 暴力使用撬片会导致玻璃破裂。


    • 继续沿着下方继续滑动来将粘合剂分离。

    • 如果撬片卡住了,请沿着iPad的侧面滚动撬片,然后继续进行分离工作。


    • 将第一个插入iPad的撬片向上滑动到iPad的左上角

    • 撬片可能会出现图片上的情况,请不要慌张。 只需将撬片拉出一点点来继续进行维修工作。 但要避免这种情况,因为粘合剂可能会粘附在LCD显示屏上变得难以清理。


    • 重新加热iOpener 并将其放置在iPad顶部边缘位置且高于前置摄像头。

      • 小心,请勿在维修过程中过度加热iOpener。 在重新加热iOpener之前请至少等待10分钟。

    • 如果您有可以弯折的iOpener,您可以弯折其使其同时加热左上角边缘位置。


    • 在左顶部插入撬片来分离粘合剂。

    Gezz this is though! Cracked the glass while replacing it.

    Padraic Hoselton - 回复

    • 滑动撬片直到快接近前置摄像头位置时停下

    • 第三张图片展示了iPad前置摄像头的位置。

      • 避免使用撬片直接滑过前置摄像头,这样做可能会污损到摄像头。 接下来的步骤将会详细说明如何避免损伤前置摄像头。


    • 轻轻拉出些许撬片,并沿着前置摄像头顶部位置慢慢的滑动。


    • 将刚才那片撬片稍微滑过前置摄像头然后放在原位不动。

    • 拿另一片撬片插入到摄像头的左侧位置然后滑动到转角位置,完成对该边缘部分的粘合剂分离工作。

    • 将第二片撬片放在转角处,防止粘合剂冷却后重新粘连。


    • 将刚才那片撬片稍微深入iPad之中,从摄像头处滑动到右上角。


    • 将三个撬片放置在转角处,防止粘合剂重新与粘连前面板。

    • 重新加热iOpener然后将其放置在iPad未撬开的右侧,音量和电源键一侧。


    • 滑动右上角的撬片,分离那部分的粘合剂。

    • 将这个撬片就放在这,防止粘合剂重新粘连。 重新拿一个撬片来进行下一步。


  3. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • 在右侧插入一个新的撬片来分离粘合剂,滑动到中部位置时停下。


    • 继续滑动到右下角处,来分离粘合剂。


    • 就把撬片放在停下的位置,然后重新加热iOpener。

      • 记住,切勿过度加热iOpener-加热间隔为10分钟。

    • 然后将iOpener放置在iPad的底部几分钟来软化玻璃面板下的粘合剂。


    • 滑动左下边的撬片来分离粘合剂。

    • 滑动到左下角时停止滑动。 然后放置在此

    • 这里有几个地方需要避免撬动到。 详见第三张图片。

      • 天线

      • Home键

      • 数字化线缆

    • 接下来的步骤将会指导您如何避免伤害这些部件。 只加热和撬动指南所指示的部位。


    • 将原撬片放置在原位,以防粘合剂重新粘合。

    • 拿一片新的撬片,轻轻的从左手边的天线处滑动到home键前

      • 只能从iPad外边缘向内滑动 请勿按照相反方向滑动 这样可能会损坏天线。

      • 如果您需要再次滑动来清理粘合剂,请取出撬片然后从外边缘重新插入再向内滑动。

    • 将撬片放置不动。


    • 拿一片新的撬片来从刚才那片撬片在右边Home键下继续滑动。

    • 在右手边大约1英尺的地方停下来,避免切割到数字化线缆。

    • 将撬片稍微深入,然后向Home键处滑动。

    • 再一次提醒,确保完全插入然后再滑动撬片。 不然的话这样会损坏玻璃面板下的天线。


    • 重新加热iOpener 将其放在iPad的顶端。


    • 小心操作这一步,花点时间保证粘合剂是热和软的,同时确保您的撬片已经分离开了该分离的粘合剂。 不要怕返工和重新加热。

    • 在iPadHome键相对的顶部您应该在每个角落里插了撬片。 扭动撬片,轻轻地提起玻璃面板,分离最后残留的粘合剂。

    • 如果在打开过程中遇到很大的阻力,请立即停止扭动撬片。 将撬片放置原位,重新加热iOpener,将其放置在难以开启的位置,然后插入撬片来重新分离一遍粘合剂。


    • 慢慢地轻轻地提起玻璃面板,以便沿着下边缘进一步分离粘合剂。


    • 一旦所有的粘合剂被分离了,玻璃面板就可以像翻书一样将其放置在您的工作台上。


    • 前置摄像头的保护壳可能会粘在前面板上; 将保护壳从面板上取下,并放回相机上以保护相机模组。

    • 从保护壳一角晃动其,让其从前面板上的粘合剂上分离下来。

    • 将前置摄像机外壳放回后壳中的凹槽。


    • 小的海绵胶带保护着顶部,底部右手边有螺丝将LCD与后壳相固定。

    • 使用镊子取下保护右上侧LCD螺丝的长方形海绵胶带。

    • 取下右下方LCD螺丝上的长方形胶带。


    • 左上方的LCD螺丝有可能被胶带所覆盖。

    • 如果有的话,使用撬棒扁平的一端来撬起,露出下方的LCD螺丝。


    • 移除将LCD与后壳固定的四颗3.9 mm Phillips #000 螺丝。

    In my case the 4 screws are not the same. One is 4mm, and 3 of 3.5mm, or better 2 x 3.5mm and one 3.45mm. I put the longest one at the left edge at left of the LCD flat cable.


    Mitja Jankovic - 回复

    Hi Mitja. I just checked the measurements with an electronic digital caliper. I got 3.9 mm for all four screws. Are you sure it was the same model? Thanks.

    Walter Galan -

    The top left screw is longer than the other 3 - iPad mini Retina Wi-Fi.

    sandro - 回复

    On mine the top right screw is longer

    oliver - 回复

    top right is longer on an ipad mini 2 retina wifi 32GB

    sagert - 回复

    • 使用镊子来将LCD框架与右侧扬声器连接的胶带剥离。

    I wonder what does this sticker stands for…

    K8L - 回复

    • LCD框架上贴着一条薄薄的海绵胶带,将LCD面板下方的胶带相连接。 要继续,你需要将其破坏然后剥离一些,暴露下方的胶带。

    • 使用薄口镊子拉起LCD周围的泡沫胶带的顶部。

      • 不要用镊子触碰液晶显示器,否则可能会损坏显示屏。

    • 使用镊子将泡沫胶带剥去以暴露液晶显示屏的顶部。


    • 在LCD框与LCD顶部胶带之间插入撬棒的尖端。

    • 在LCD框与胶带之间滑动,将胶带与LCD框相分离。

    I finished a successful replacement of my screen following these instructions. Thanks.

    Step 36 (remove tape from LCD perimeter), however, seems unnecessary. I ended up spending a lot of time separating the tape from the LCD frame only to discover it was not necessary for steps 37-44 and actually made things really difficult for step 45-46 (removing the tape near the speakers). Finally, steps 45-46 can be skipped since it is much easier to remove this tape once you flip the LCD over (Step 55).

    Kenneth Snyder - 回复

    • LCD金属屏蔽版与LCD使用胶水在其顶部左侧和右侧的边角相粘连。 为了安全分离这些粘合剂,你需要使用吉他拨片来移动几毫米。

    • 在LCD与后壳靠近左上角的位置插入吉他拨片

    • 小心向外弯曲拨片,不需要撬开过大的缝隙。

    I found a very simple method for removing the LCD from the metal shield. Slightly lift one of the top corners and insert a 1' piece of fishing line. Insert the line under the other top corner placing the length between the LCD and shield. Once in place, gently pull each end toward the bottom of the LCD breaking the adhesive as you go. This will make things much easier than using the picks and possibly breaking the LCD.

    bababooey - 回复

    The fishing line trick is amazing… although i had already broken the LCD when i saw that comment. Good Learn!

    Brandon Lukasik - 回复

    This step is what destroys my LCDs :(

    Dan Harris - 回复

    Just destroyed my LCD as well. A red warning remarking is missing here! The LCD assembly is very fragile an cannot be bent, even slightly!!

    brauliox - 回复

    I have broken about 10 of the 50 or so iPad minis that I have repaired. I always try to have a LCD on hand. I’ll have to try the fishing line trick!

    northstar - 回复

    I also recommend doing step 45 first (removing the two pieces of foam tape at the bottom).

    northstar - 回复

    • 将吉他拨片器入液晶显示屏左侧的三个位置,并在每个位置弯曲,将液晶显示转到后壳的右侧。


    • 现在到了液晶显示屏的右侧,并沿着旁边的几个地方使用吉他拨片撬动,将液晶显示屏移回左边。

    • 重复此操作和上一步骤几次,直到LCD容易左右移动。


    • 在接下来几步中,你将使用撬棒在LCD与金属背板之间滑动来将LCD从下方的粘合剂中分离出来。

    • 将撬棒扁平的一端插入LCD框与金属背板之间。

      • 确保撬棒位于LCD框与背板之间,而不是在背板的下方。 撬起背板将会损坏部件,因为在LCD下方螺丝将背板与后壳固定。


    • 从设备的右上角开始,将撬棒滑入LCD框和金属背板之间,当您推动撬棒时也会分离两者之间的粘合剂。

      • 我们的目标是分离粘合剂,而不是撬起LCD。 所以尽量小角度撬动,防止损伤LCD。

    • 如果在LCD边角处深入撬棒会使得LCD弯曲,使用吉他拨片来重复上述动作来进一步分离粘合剂。

    These steps were hard. I was too scared that I was going to brake the LCD. Luckily I got it off! Don’t know how delicate these things are and how much force they can take.

    Padraic Hoselton - 回复

    • 重复先前的步骤来分离LCD顶部。

    • 将撬棒扁平的一端插入LCD框与金属背板之间,小心地在顶部推动撬棒,分离粘合剂。


    • 在LCD左侧继续进行相同的操作,将撬棒扁平的一端尽可能深的插入LCD和背板之间。

    • 这时,LCD应该与固定的粘合剂分离了,如果没有的话,重新在右侧或者顶部插入撬棒来完全分离LCD。


    • 从后壳上抬起LCD几英寸,来确保它已完全与粘合剂相分离。


    • 两条宽胶带将LCD与扬声器相连。

    • 一只手拿着LCD, 另一只手将撬棒扁平一端插入左扬声器与胶带之间的空隙之间。

    • 将液晶显示器从扬声器中轻轻拉出,同时向外旋转撬棒将胶带与扬声器分离。

    I recommend removing these two pieces of foam tape prior to loosening and lifting the LCD.

    northstar - 回复

    • 将撬棒扁平一端插入右扬声器与胶带之间的空隙之间。

    • 将液晶显示器从扬声器中轻轻拉出,同时向外旋转撬棒将胶带与扬声器分离。


    • 将LCD翻转并放在前面板玻璃的顶部。

    • 不要尝试从iPad上取下LCD,因为它仍有排线线连接。


    • 移除下列将LCD屏蔽板与后壳固定的螺丝。

      • 2颗2.6 mm Phillips #00 螺丝

      • 13颗 1.7 mm Phillips #00 螺丝

      • 在有些设备上,额外的一颗1.7 mm Phillips #00螺丝。

    At the iPad mini retina Wi-Fi there are only 7 screws.

    sandro - 回复

    On my iPad Mini (Gen 1 WiFi; A1432), these are not #00 screws, but #000 screws. They're much tinier than the first four screws that held the LCD tabs in place. The #00 driver sorta works, but requires a lot of force to get traction. The #000 driver works like a charm, though.

    volty - 回复

    On my 1432 there were mixed in 4 tiny #000 screws holding the shield plate aong the right side. Looks like these can be mixed in without consequence as they are shorter anyway

    gfriedman99 - 回复

    • 在LCD屏蔽板Home键的正下方插入撬棒扁平的一端。

    • 撬起撬棒,来将屏蔽板与后壳分离。


    • 将屏蔽板从iPad中移除。


    • 移除固定连接器支架的三颗 1.3 mm Phillips #00 螺丝

    • 确保这三颗螺丝没有与其他螺丝弄混, 任何稍长的螺丝可能会损坏螺丝孔,导致逻辑板的不可修复的损坏。

    Note: These three screws are smaller than the rest of the screws holding the larger LCD shield although they look similar. If you substitute the larger screws, you will pop a screw bracket which can damage the board on both the mini original and mini 2 retina. I just wrote a blog post about how this happens: http://mendonipadrehab.com/entries/gener...

    jessabethany - 回复

    Hi jessabethany. Thank you for the warning. I read your blog post and found it to be very informative. Thanks for adding the warning to the step. It will most definitely help others avoid any damage to the logic board. Thanks!

    Walter Galan -

    Be careful: At iPad mini retina Wi-Fi there are thw short and one longer screw! Don't mix them!

    sandro - 回复

    • 使用镊子将支架从iPad中移走。


    • 使用塑料打开工具,轻轻地将电池连接器从逻辑板上的插座中撬起。

    • 千万小心地来撬起连接器,切勿直接撬动插座。 这样做将会完全损坏连接部分。

    Make sure you disconnect the battery. If not and ipad is still on you can have problems with the LCD backlight. To fix that problem you have to solder

    Mattis - 回复

    I may be experiencing the backlight problem you mentioned. What connection needs to be soldered?

    Grillwrecka -

    Have an issue - heard that if you don't disconnect the battery a fuse is blown. I need help to fix the blown fuse.

    Andrew Kivell -

    There is an extensive thread in Answers about iPad mini backlight problems.Th screen stays black after a digitizer replacement.

    jessabethany -

    After unplugging the battery place a guitar pick in-between the two connections.

    While continuing to work on the iPad you may inadvertently cause the two connections to touch.

    Michael Vovaris - 回复

    Yeah, you need to put the pick in between the connections so the battery doesn't touch the logic board connector and blow a fuse and make your backlight not turn on. You really don't want to have to solder the 2 connections together, especially if you don't know how, like me! I will use your comment's advice when working.

    WolfyHD - 回复

    I put a piece of cellotape on the contact side of the connector and could happily forget about it while getting on with the rest of the repair.

    Rory Filer - 回复

    • 使用塑料打开工具来将LCD连接头从逻辑板上的插座中撬起。

    • 切勿靠着IC芯片来撬动,这样会损坏IC芯片。 如图小心在边缘处撬动。

    Putting the iPad back together: While plugging the LCD Connector back in, take your time finding the socket on the logic board. Do no use pressure until you are certain it is seated properly. Trust me, if you take your time you will know its seated correctly.

    Michael Vovaris - 回复

    • LCD此时仍通过下方的两条宽胶带与后壳连接。

    • 一只手握住LCD,将撬棒插入左侧的胶带和LCD之间。

    • 向外滑动撬棒,分离胶带。 将LCD小心向外提起,使其远离胶带。

    • 在分离LCD与胶带的时候,扭动撬棒会更加高效的分离。

    Removing this tape and such to take the LCD off completely is unneccessary when replacing just the glass and digitizer, the digitizer cable is easily removed without further work to the LCD

    Nick Hughes - 回复

    When this tape damage, how we can take a new?

    Muhammed Kilic - 回复

    When this tape are damage, how we can order and take a new one?

    Muhammed Kilic - 回复

    Following from Nick H’s comment about LCD removal being unnecessary - I tried that first and got my broken glass OUT of the assembly by threading it thru a limited space beneath the LCD. Later when trying to reseat the digitizer connector I gave up and removed the LCD anyhow. Not that much extra work but a LOT easier to install the digitizer and reseat the connector without having to navigate around the LCD and its cable. Removal of the tape holding the LCD was easy - there are two short lengths of rubber or foam along the bottom edge of the LCD that faces the outside world. Remove those(save them) and then _carefully_ peel up the tape; I saw some metallic looking residue underneath. Later when re-assembling everything, I put the tape back and then those two short lengths of foam.

    Rory Filer - 回复

    • 仍用一只手握住LCD,按照先前操作方法来移除左侧的胶带。

    • 将撬棒扁平的一端插入LCD框与胶带之间,向外滑动撬棒,然后轻轻提起LCD。


    • 将LCD从iPad mini 中分离出来。







Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Andrew Optimus Goldberg


394,763 信誉积分



iFixit iFixit 的会员


113 名成员


you are the truth!

thisismrkia - 回复

Good guide. Will I need a new LCD shield plate, or can I use the old one?

slapstick4235 - 回复



过去的24小时: 5

过去的7天: 45

过去的30天: 175

总计 26,392