菜单

你的设置

我的工作台

快速访问设备的指南，配件和论坛
我的购物车

购物车是空的

浏览我们的商店

iMac Intel 24" EMC 2134 and 2211 Hard Drive Replacement

撰写者： Brittany McCrigler (和另外3个贡献者)
  • 评论： 9
  • 收藏 1

难度

中等

步骤

7

所需时间

建议一个时间??

节

1

标志

1

Prerequisite Only

仅作为前提条件

请注意，本指南只是其他指南的前提条件。

简介

Use this guide to install a hard drive in your iMac Intel 24" EMC 2134 or 2211.

工具

购买这些工具

配件

没有特定配件。

  1. If necessary, remove the pieces of tape securing the hard drive/optical drive thermal sensor cables to your iMac.

    • If necessary, remove the pieces of tape securing the hard drive/optical drive thermal sensor cables to your iMac.

    翻译

  2. Disconnect the hard drive thermal sensor by pulling its connector upwards toward the top of your iMac.

    • Disconnect the hard drive thermal sensor by pulling its connector upwards toward the top of your iMac.

    • When removing this connector, it is helpful use your thumbnails to push the ears on either side of the connector toward the top of your iMac.

    翻译

  3. Pressing the top of the hard drive bracket down to release it from the rear case requires a substantial amount of force. We recommend laying your iMac stand-side down on a table to avoid knocking it over. Press the hard drive bracket down toward the bottom edge of your iMac to free it from the rear case, then rotate the top of the drive toward yourself.

    • Pressing the top of the hard drive bracket down to release it from the rear case requires a substantial amount of force. We recommend laying your iMac stand-side down on a table to avoid knocking it over.

    • Press the hard drive bracket down toward the bottom edge of your iMac to free it from the rear case, then rotate the top of the drive toward yourself.

    翻译

  4. PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物

    PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物

  5. Rotate the hard drive toward yourself, then lift it up off its mounting pins. The hard drive is still connected via the SATA cables.

    • Rotate the hard drive toward yourself, then lift it up off its mounting pins.

    • The hard drive is still connected via the SATA cables.

    • When reinstalling your hard drive, be careful not to push the rubber grommets through the openings in the chassis with the lower hard drive pins as retrieving them may require logic board removal.

    翻译

  6. Insert the flat end of a spudger between the SATA power cable connector and the edge of the hard drive.

    • Insert the flat end of a spudger between the SATA power cable connector and the edge of the hard drive.

    • Twist the spudger to separate the connector from the hard drive.

    翻译

  7. Pull the SATA power connector away from the hard drive.

    • Pull the SATA power connector away from the hard drive.

    翻译

  8. Disconnect the SATA data cable by pulling its connector away from the hard drive.

    • Disconnect the SATA data cable by pulling its connector away from the hard drive.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Brittany McCrigler

于2012年03月05日注册

82,096 信誉积分

创作了132篇指南

徽章: 48

+ 45更多徽章

团队

iFixit iFixit 的会员

Community

99 名成员

创作了9,303篇指南

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 1

总计 535