修复你的物品

维修的权力

商店

iMac Intel 21.5" EMC 2638 Fan Replacement

撰写者： Sam Goldheart (和另外4个贡献者)

评论： 41
收藏 2
完成 8

iMac Intel 21.5" EMC 2638 Fan Replacement

难度

中等

步骤

26

所需时间

30分钟 - 1小时

简介

Use this guide to replace the fan.

工具

购买这些工具

配件

购买这些配件

iMac Intel 21.5" (Late 2012 - Mid 2014) CPU Fan

$24.99

购买
iMac Intel 21.5" (2012-2019) Adhesive Strips

$19.99

购买

步骤 1 Display Assembly

With the hinge free to move, the iMac will be unbalanced and hard to work on. Repairs are fast and easy with an iMac service wedge, but can be completed without one.

在这个步骤中使用的工具：

iMac Service Wedge

With the hinge free to move, the iMac will be unbalanced and hard to work on. Repairs are fast and easy with an iMac service wedge, but can be completed without one.
If you are using the iFixit cardboard service wedge, follow these assembly directions to put it together.
Before beginning any work on your iMac: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply's capacitors.
Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.

步骤 2

Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear enclosure.

The hub on the iMac Opening Tool will keep you from pushing the wheel in too far. If using a different tool, insert no more than 3/8" into the display. Otherwise, you risk severing antenna cables and causing serious damage.

Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear enclosure.
The hub on the iMac Opening Tool will keep you from pushing the wheel in too far. If using a different tool, insert no more than 3/8" into the display. Otherwise, you risk severing antenna cables and causing serious damage.

步骤 3

Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.

Be sure to always push with the handle behind the cutting wheel. If you pull, the wheel might get pulled out of the handle.

Run the tool up along the left side of the display.

Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.
Be sure to always push with the handle behind the cutting wheel. If you pull, the wheel might get pulled out of the handle.
Run the tool up along the left side of the display.

步骤 4

Continue running the tool up around the top left corner.

Continue running the tool up around the top left corner.

Continue running the tool up around the top left corner.

Continue running the tool up around the top left corner.

步骤 5

Cut the adhesive along the top left of the display.

Cut the adhesive along the top left of the display.

Cut the adhesive along the top left of the display.

步骤 6

Continue along the top of the display.

You may want to run the tool back and forth through what you've already cut a few times, to ensure you get as much of the adhesive separated as possible.

Continue along the top of the display.
You may want to run the tool back and forth through what you've already cut a few times, to ensure you get as much of the adhesive separated as possible.

步骤 7

Push the tool around the top right corner of the display.

Push the tool around the top right corner of the display.

Push the tool around the top right corner of the display.

Push the tool around the top right corner of the display.

步骤 8

Wheel the tool down along the right side of the display.

Wheel the tool down along the right side of the display.

Wheel the tool down along the right side of the display.

步骤 9

Finish pushing the opening tool to the bottom of the right side of the display.

At this point, you'll want to run the tool back around the entire display, to ensure you cut as much adhesive as possible.

Finish pushing the opening tool to the bottom of the right side of the display.
At this point, you'll want to run the tool back around the entire display, to ensure you cut as much adhesive as possible.

步骤 10

While the opening tool cut most of the adhesive, the display will still be slightly adhered to the case. A plastic card will be necessary to free up the last of this adhesive.

Set the iMac face-up on a table.

Starting from the top right corner of the iMac, wedge a plastic card between the display and frame.

While the opening tool cut most of the adhesive, the display will still be slightly adhered to the case. A plastic card will be necessary to free up the last of this adhesive.
Set the iMac face-up on a table.
Starting from the top right corner of the iMac, wedge a plastic card between the display and frame.
Be careful not to insert the plastic card more than 3/8", or you may damage internal components.

步骤 11

Gently twist the plastic card sideways to create a gap between the display and frame.

Move slowly and be careful not to stress the display glass too much—you only need to make a gap of about 1/4".

Gently twist the plastic card sideways to create a gap between the display and frame.
Move slowly and be careful not to stress the display glass too much—you only need to make a gap of about 1/4".

步骤 12

Slide the card toward the center of the display to cut any of the remaining adhesive along the top right corner of the iMac.

Be sure to stop before the iSight camera, or you may damage it.

Be sure to stop before the iSight camera, or you may damage it.

Slide the card toward the center of the display to cut any of the remaining adhesive along the top right corner of the iMac.
Be sure to stop before the iSight camera, or you may damage it.

步骤 13

Wedge the plastic card into the top right corner once again, and leave it there to prevent the adhesive from resticking.

Wedge the plastic card into the top right corner once again, and leave it there to prevent the adhesive from resticking.

Wedge the plastic card into the top right corner once again, and leave it there to prevent the adhesive from resticking.

步骤 14

Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.

Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.

Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.

Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.

步骤 15

Gently twist the card upward, slightly increasing the space between the display and frame.

As with the other side, twist slowly to allow the adhesive time to separate, and be careful not to over-stress the display glass.

Gently twist the card upward, slightly increasing the space between the display and frame.
As with the other side, twist slowly to allow the adhesive time to separate, and be careful not to over-stress the display glass.

步骤 16

Slide the plastic card toward the center, again stopping just before the iSight camera.

Slide the plastic card toward the center, again stopping just before the iSight camera.

Slide the plastic card toward the center, again stopping just before the iSight camera.

Slide the plastic card toward the center, again stopping just before the iSight camera.

步骤 17

Wedge the plastic card back into the top left corner.

Wedge the plastic card back into the top left corner.

Wedge the plastic card back into the top left corner.

步骤 18

With both plastic cards inserted as shown near the corners, gently twist the cards sideways to increase the gap between display and case.

If there are any sections that seem to stick and won't separate, stop twisting and use one of the cards to cut the remaining adhesive.

Begin to lift the top of the display up from the frame.

With both plastic cards inserted as shown near the corners, gently twist the cards sideways to increase the gap between display and case.
If there are any sections that seem to stick and won't separate, stop twisting and use one of the cards to cut the remaining adhesive.
Begin to lift the top of the display up from the frame.
Only lift the display a few inches—the display data and power cables are still connected to the logic board.

步骤 19 Display

While holding the display up with one hand, use the other hand to unplug the display power cable.

Lift the display up enough to have easy access to the connector, but not so much that you stretch the cables and stress their connections (about 8").

While holding the display up with one hand, use the other hand to unplug the display power cable.
Lift the display up enough to have easy access to the connector, but not so much that you stretch the cables and stress their connections (about 8").

步骤 20

Use the tip of a spudger to flip up the metal retaining bracket on the display data cable.

Carefully pull the display data cable from its socket on the logic board.

Be sure to pull the display data cable connector straight out of its socket.

Use the tip of a spudger to flip up the metal retaining bracket on the display data cable.
Carefully pull the display data cable from its socket on the logic board.
Be sure to pull the display data cable connector straight out of its socket.

步骤 21

Lift the display up to a near-vertical position.

At this point there is still a strip of adhesive along the bottom of the display, that will hold the display to the frame like a hinge. You can loosen this adhesive by working the display up and down a few times.

Lift the display up to a near-vertical position.
At this point there is still a strip of adhesive along the bottom of the display, that will hold the display to the frame like a hinge. You can loosen this adhesive by working the display up and down a few times.

步骤 22

If necessary, a plastic card can be used to cut any remaining sections of the bottom adhesive strip.

If necessary, a plastic card can be used to cut any remaining sections of the bottom adhesive strip.

If necessary, a plastic card can be used to cut any remaining sections of the bottom adhesive strip.

步骤 23

Lift the display up from the frame and remove it from the iMac.

It may be necessary to slowly lift from one side, to peel against the remaining adhesive.

Be very careful handling the display—it's big, heavy, and made of glass.

Lift the display up from the frame and remove it from the iMac.
It may be necessary to slowly lift from one side, to peel against the remaining adhesive.
Be very careful handling the display—it's big, heavy, and made of glass.
During reassembly, head over to our display adhesive guide to install the new adhesive.

步骤 24 Fan

Pull the fan cable connector straight away from its socket on the logic board.

Pull the fan cable connector straight away from its socket on the logic board.

Pull the fan cable connector straight away from its socket on the logic board.

步骤 25

Remove the three 12.3 mm T10 shoulder screws from the fan enclosure.

Remove the three 12.3 mm T10 shoulder screws from the fan enclosure.

步骤 26

Lift and remove the fan from the iMac.

Lift and remove the fan from the iMac.

Lift and remove the fan from the iMac.

结论

To reassemble your device, follow these instructions in reverse order.

8等其他人完成本指南。

作者

与4其他贡献者

Sam Goldheart

于2012年10月18日注册

436,316 信誉积分

创作了547篇指南

+ 45更多徽章

团队

iFixit iFixit 的会员

Community

134 名成员

创作了15,565篇指南

0条评论

添加一条评论

浏览统计数据:

过去的24小时： 2

过去的7天： 6

过去的30天： 38

总计 2,833