菜单

你的设置

我的工作台

快速访问设备的指南，配件和论坛
我的购物车

购物车是空的

浏览我们的商店

iMac G5 17" Model A1144 IR Board Replacement

撰写者： Walter Galan (和另外3个贡献者)
  • 评论： 3
  • 收藏 0

难度

中等

步骤

13

所需时间

建议一个时间??

节

3

标志

0

简介

The ins and outs of replacing your IR board.

工具

购买这些工具

配件

无需配件。

  1. 步骤 1 Access Door

    Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Loosen the two Phillips screws securing the access door to your iMac.

    • These screws are captive in the access door.

    翻译

    添加评论

  2. 步骤 2

    Remove the access door from your iMac.

    • Remove the access door from your iMac.

    翻译

    添加评论

  3. 步骤 3 Front Bezel

    • Remove the three T8 Torx screws securing the front bezel to the rear panel.

    翻译

    添加评论

  4. 步骤 4

    • Orient the iMac face-up, on its backside.

    • Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    翻译

    添加评论

  5. 步骤 5

    • While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    翻译

    添加评论

  6. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12

  7. 步骤 6

    • Re-orient your iMac so it sits upright on the stand.

    • Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

    • Push the card toward the top of the iMac to release the front bezel latch.

    • Pull the front bezel away from the rear case.

    • Repeat this process for the other side of the front bezel.

    • It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.

    • If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

    翻译

    Using a strongish magnet will grab and release the latches.

    darkstar448 - 回复

    来自 darkstar448 的话:

    Using a strongish magnet will grab and release the latches.

    Are you sure it's safe to do this? How close is the hard drive, won't magnets interfere with it?

    Sarah - 回复

    It's almost certainly fine. Modern hard drives are very resistant to magnetic fields.

    zschroeder6212 -

  8. 步骤 7

    • Lay your iMac stand-side down on a table.

    • Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.

    • Lay the front bezel above the rest of the iMac.

    翻译

    添加评论

  9. 步骤 8

    • If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    翻译

    添加评论

  10. 步骤 9

    • Disconnect both the camera and microphone cables.

    翻译

    添加评论

  11. 步骤 10 IR Board

    • Peel back the aluminum EMI shield up off the lower three edges of the rear case.

    • It is not necessary to peel the EMI shield off the display.

    • We found it helpful to tape the EMI shield up against the display to keep it out of the way.

    翻译

    添加评论

  12. 步骤 11

    • Remove the single T6 Torx screw securing the IR board bracket to the logic board.

    • The IR board and cable finger are now free from the logic board and may fall.

    翻译

    添加评论

  13. 步骤 12

    • Pull the IR Board cable connector straight away from its socket on the IR board.

    翻译

    添加评论

  14. 步骤 13

    • Transfer the two T6 Torx screws and the IR bracket to your new IR board.

    翻译

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 0

总计 4,020