修复你的物品 社区 商店

iDea USA CT702 Digitizer Glass Replacement

简介

This guide provides quick and easy steps for the replacement of a digitizer glass intended for an iDea USA CT702 tablet.

你所需要的

  1. iDea USA CT702 Digitizer Glass Replacement, Digitizer Glass: 步骤 1 中的图像 1，1

    • Place tablet on the table with screen facing upright.

    • Starting from the portholes, use plastic opening tool to pry in between the front panel and back cover.

    • Follow the opening along the corners and sides until all latches are unclipped.

    • Remove back cover completely and place it outside of the work area.

    编辑

  2. iDea USA CT702 Digitizer Glass Replacement: 步骤 2 中的图像 1，2 iDea USA CT702 Digitizer Glass Replacement: 步骤 2 中的图像 2，2

    • Place tablet facing down.

    • Locate the 4mm screws along the perimeter of the motherboard.

    • There should be 4 screws.

    • Use Philips screw driver to unscrew each one, and carefully place screws in a safe place.

    编辑

  3. iDea USA CT702 Digitizer Glass Replacement: 步骤 3 中的图像 1，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 3 中的图像 2，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 3 中的图像 3，3
    在这个步骤中使用的工具：
    Tweezers
    $4.99
    购买

    • After screws are removed, gently pull up on the ribbon wire connection to release all 3 wires from the motherboard.

    • Safely remove mother board and battery from tablet by using tweezers.

    • Make sure the small ribbon wires are not damaged when removing larger members.

    编辑

  5. iDea USA CT702 Digitizer Glass Replacement: 步骤 4 中的图像 1，1

    • Remove tape from battery pack, and dispose.

    • Be careful not to touch the wire/battery connection correctly, as it could result in injury.

    编辑

  6. iDea USA CT702 Digitizer Glass Replacement: 步骤 5 中的图像 1，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 5 中的图像 2，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 5 中的图像 3，3

    • After removing the battery pack and motherboard, the touch sensor unit should be visible.

    • Use small Philips screw driver to unscrew all 6 of the 2mm screws.

    • Use fingers and prying tool to remove the touch sensor unit from frame.

    编辑

  7. iDea USA CT702 Digitizer Glass Replacement: 步骤 6 中的图像 1，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 6 中的图像 2，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 6 中的图像 3，3

    • After the touch sensor is detached, only the plastic screen should remain.

    • Insert new touch sensor plate into the same position, aligning all screw inputs.

    • Insert all six of the 2mm. screws to connect the new touch sensor to the screen frame.

    编辑

  8. iDea USA CT702 Digitizer Glass Replacement: 步骤 7 中的图像 1，1

    • To continue reassembling the tablet, follow the steps in reverse.

    • Be careful when reconnecting battery, use safety goggles and gloves.

    编辑

  9. iDea USA CT702 Digitizer Glass Replacement: 步骤 8 中的图像 1，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 8 中的图像 2，3 iDea USA CT702 Digitizer Glass Replacement: 步骤 8 中的图像 3，3

    • To reassemble tablet, follow these steps in reverse order.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与7其他贡献者

David Kambich

于03/11/15注册

110 声望

撰写一个指南

徽章: 4

+1个徽章

团队

Colorado Springs, Team 4-7, Panko Spring 2015 Colorado Springs, Team 4-7, Panko Spring 2015 的会员

UCCS-PANKO-S15S4G7

3 名成员

创作了10篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 2

过去 30 天： 3

总计 326