修复你的物品 社区 商店

认识和断开线缆连接头

返回指南
英语
中文
下一步

正翻译步骤 1

步骤 1
Recognizing & Disconnecting Cable Connectors, ZIF Connectors: 步骤 0 中的图像 1，3 Recognizing & Disconnecting Cable Connectors, ZIF Connectors: 步骤 0 中的图像 2，3 Recognizing & Disconnecting Cable Connectors, ZIF Connectors: 步骤 0 中的图像 3，3
ZIF Connectors

  • Zero insertion force (ZIF) connectors are often used to secure delicate ribbon cables of many sizes. A hinged locking flap runs across the top of the socket, and the cable is inserted on one of the long edges.

  • To disconnect the cable, use a spudger, opening tool, or a clean fingernail to flip up the locking flap—this is the unlocked position.

  • Use the widest tool possible to avoid damaging the delicate hinge pins.

  • Once the flap is in the unlocked position, use tweezers or your fingers to gently pull the cable out of its socket.

  • If the cable has a pull tab, use it to grip the cable. You may damage the cable by gripping it directly.

  • Some cables may have small "arms" or notches that help secure them. If this is the case, you'll need to lift the cable to free it and then pull it out.

  • To reconnect, make sure the locking flap is flipped up and gently reinsert the cable. Then, flip the locking flap down to secure the cable. The cable should slide into the socket with little to no force. If you're having trouble, remove it, check that the flap is fully unlocked, and try again.

  • Some cables (like the one pictured) may have a line that marks the edge of the connection area. Make sure you insert the cable so the line is flush with the edge of the socket.

ZIF 接口

零插入力（ZIF）连接器通常会给初学者带来麻烦。 ZIF连接器用于固定精细的带状电缆，如FFC（扁平柔性电缆）或FPC（柔性印刷电路）电缆。

顾名思义，不需要力量来插拔电缆。

要断开电缆连接，请使用撬棒或指甲的尖端将小的锁片翻起。 然后，您可以安全地拉出电缆。

请确保你撬动的是小锁片而不是插座本身。

此带状电缆上的白线标记连接区域的边缘。 要重新安装，将电缆插入连接器直到对准该线，然后锁定挡板。 如果电缆不容易插入（或非常接近）该线，则可能是未对准，需要轻轻移走并重新定位。

[title] ZIF Connectors
-[* black] The ***zero insertion force (ZIF)*** connector often causes trouble for beginners. ZIF connectors are used to secure delicate ribbon cables, such as FFC (flat flex cables) or FPC (flexible printed circuit) cables.
- [* icon_note] As the name implies, no force is needed to plug in or remove the cable.
-[* black] To disconnect the cable, use the tip of a spudger or your fingernail to flip up the small locking flap. Then, you can safely pull the cable out.
- [* icon_caution] Be sure to pry up on the hinged flap, not the connector socket.
-[* icon_reminder] The white line on this ribbon cable marks the edge of the connection area. To reinstall, insert the cable into the connector up to this line, and then close the locking flap. If the cable doesn’t insert easily up to (or very near to) this line, it’s probably misaligned and needs to be gently removed and repositioned.
+[* icon_note] [link|https://en.wikipedia.org/wiki/Zero_insertion_force|Zero insertion force (ZIF) connectors|new_window=true] are often used to secure delicate ribbon cables of many sizes. A hinged locking flap runs across the top of the socket, and the cable is inserted on one of the long edges.
+[* black] To disconnect the cable, use a spudger, opening tool, or a clean fingernail to flip up the locking flap—this is the unlocked position.
+ [* icon_note] Use the widest tool possible to avoid damaging the delicate hinge pins.
+[* black] Once the flap is in the unlocked position, use tweezers or your fingers to gently pull the cable out of its socket.
+ [* icon_note] If the cable has a pull tab, use it to grip the cable. You may damage the cable by gripping it directly.
+ [* icon_note] Some cables may have small [link|https://guide-images.cdn.ifixit.com/igi/23JriT5JEeAnnoso.full|"arms"|new_window=true] or [link|https://guide-images.cdn.ifixit.com/igi/lc23VqUExNUhL1tV.full|notches|new_window=true] that help secure them. If this is the case, you'll need to lift the cable to free it and then pull it out.
+[* icon_reminder] To reconnect, make sure the locking flap is flipped up and gently reinsert the cable. Then, flip the locking flap down to secure the cable. ***The cable should slide into the socket with little to no force.*** If you're having trouble, remove it, check that the flap is fully unlocked, and try again.
+ [* icon_note] Some cables (like the one pictured) may have a line that marks the edge of the connection area. Make sure you insert the cable so the line is flush with the edge of the socket.

您的所有投稿皆享有基于开源创作共享许可协议（CC BY-NC-SA）的著作权利。