跳转到主内容

修复你的物品

维修的权力

商店

简介

In order to replace components like the CD drive, the motherboard access panel must first be removed.

配件

没有特定配件。

  1. It should be noted that these guides are written based on a late-model eMac (2005, 1.42GHz, DDR). They will differ slightly from the older model eMacs that use PC-133 RAM. Lay the eMac screen-down on a flat surface. I've found it convenient to use a carpeted floor because the computer is so heavy. Remove the single phillips #2 screw on the RAM door, and remove the door
    • It should be noted that these guides are written based on a late-model eMac (2005, 1.42GHz, DDR). They will differ slightly from the older model eMacs that use PC-133 RAM.

    • Lay the eMac screen-down on a flat surface. I've found it convenient to use a carpeted floor because the computer is so heavy.

    • Remove the single phillips #2 screw on the RAM door, and remove the door

    • The screw is captive in the door, so don't worry about losing it.

  2. Before starting this process it's important to note that the eMac can have some seriously dangerous voltages inside of it, thanks to the CRT display. Before working on an eMac, you should unplug it, press the power button to clear any stored charge on the motherboard, and then let it sit for 24-hours (or more) to allow the CRT to discharge.
    • Before starting this process it's important to note that the eMac can have some seriously dangerous voltages inside of it, thanks to the CRT display. Before working on an eMac, you should unplug it, press the power button to clear any stored charge on the motherboard, and then let it sit for 24-hours (or more) to allow the CRT to discharge.

    • You can read more about CRT safety procedures here. If you aren't experienced with working on devices featuring a CRT, it's recommended that you don't proceed any further.

    • On the bottom side of the eMac, remove the following screws:

    • A single 2.5mm hex screw

    • Two #2 phillips screws

  3. 打开所有标签

    Mac的RAM升级套装

    购买套装

    所有选项卡都有足够的 RAM

    购买套装
  4. Remove two 2.5mm hex screws from each of the other sides of the computer. Remove two 2.5mm hex screws from each of the other sides of the computer. Remove two 2.5mm hex screws from each of the other sides of the computer.
    • Remove two 2.5mm hex screws from each of the other sides of the computer.

  5. Now, the shell can almost be separated from the computer. There is a cable that connects to the power button. This must be disconnected before removing the housing completely.
    • Now, the shell can almost be separated from the computer.

    • There is a cable that connects to the power button. This must be disconnected before removing the housing completely.

    • Lift the housing enough to allow you to fit your hand through the access door, and disconnect the cable at the power button.

  6. Now the entire shell can be removed from the computer.
    • Now the entire shell can be removed from the computer.

  7. The motherboard access panel is held on by 4 phillips #2 screws. Remove the screws, then use your fingers to pull on the top tabs to separate the panel from the computer frame. Remove the screws, then use your fingers to pull on the top tabs to separate the panel from the computer frame.
    • The motherboard access panel is held on by 4 phillips #2 screws.

    • Remove the screws, then use your fingers to pull on the top tabs to separate the panel from the computer frame.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Chris Green

于2009年10月11日注册

34,298 信誉积分

创作了45篇指南

团队

Master Techs Master Techs 的会员

Community

294 名成员

创作了950篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 29

总计 598