跳转到主内容

简介

Hi Guys,


In this guide I’ll explain how to replace the Blu-ray drive it’s PCB. This is required when you swap your motherboard.

  1. First of all, remove the sticker/tape from the back of the drive to reveal the 2 other screws. You can do this with your fingers, it could take a little force, but not to much. First of all, remove the sticker/tape from the back of the drive to reveal the 2 other screws. You can do this with your fingers, it could take a little force, but not to much. First of all, remove the sticker/tape from the back of the drive to reveal the 2 other screws. You can do this with your fingers, it could take a little force, but not to much.
    • First of all, remove the sticker/tape from the back of the drive to reveal the 2 other screws. You can do this with your fingers, it could take a little force, but not to much.

  2. Remove the 4 PH1 screws. Lift up the back cover and remove it. It should not take any force and should come off easily. I lifted it up at the left side. Lift up the back cover and remove it. It should not take any force and should come off easily. I lifted it up at the left side.
    • Remove the 4 PH1 screws.

    • Lift up the back cover and remove it. It should not take any force and should come off easily. I lifted it up at the left side.

  3. Do NOT remove the ribbon cables yet, make sure you opened up the ZIF connector first and then remove the ribbon cables. Otherwise you could damage the PCB. Open up all the 3 ZIF connectors with your finger nails or with an plastic opening tool carefully. Then remove the 3 ribbon cables from their sockets.
    • Do NOT remove the ribbon cables yet, make sure you opened up the ZIF connector first and then remove the ribbon cables. Otherwise you could damage the PCB.

    • Open up all the 3 ZIF connectors with your finger nails or with an plastic opening tool carefully.

    • Then remove the 3 ribbon cables from their sockets.

  4. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  5. You will see an red and an black cable soldered to the PCB. Now get your solder iron ready to desolder the 2 cables. Heat and melt the solder, with your other hand hold the tweezer. When the solder is melting, remove the cable with your tweezer to get the cable out. It's recommended you use desoldering wick, so you can put some fresh new solder on the pads. Recommended but not required.
    • You will see an red and an black cable soldered to the PCB.

    • Now get your solder iron ready to desolder the 2 cables. Heat and melt the solder, with your other hand hold the tweezer. When the solder is melting, remove the cable with your tweezer to get the cable out.

    • It's recommended you use desoldering wick, so you can put some fresh new solder on the pads. Recommended but not required.

    • Now it should look like the last photo.

  6. Remove the tiny 3 PH1 screws from the PCB.
    • Remove the tiny 3 PH1 screws from the PCB.

  7. Hold the PCB and move it up. You should notice that PCB will come loose from the drive. Now hold in the middle and move it upward a little and the back to yourself. Be aware that it will need a little force (especially from the right side, as a clip is holding it down), but it should come off easily. That's it! You got the PCB out!
    • Hold the PCB and move it up. You should notice that PCB will come loose from the drive.

    • Now hold in the middle and move it upward a little and the back to yourself. Be aware that it will need a little force (especially from the right side, as a clip is holding it down), but it should come off easily.

    • That's it! You got the PCB out!

  8. When installing the new PCB, look out for the spots as shown in Photo 1 (red circles). When you follow photo 1 and tight it with screws, you could break the PCB ! So do the opposite of Photo 1! Photo 2 shows correctly how the PCB need to be seated. As you can see in the blue circles.
    • When installing the new PCB, look out for the spots as shown in Photo 1 (red circles). When you follow photo 1 and tight it with screws, you could break the PCB ! So do the opposite of Photo 1!

    • Photo 2 shows correctly how the PCB need to be seated. As you can see in the blue circles.

结论

To reassemble your device, follow these instructions in reverse order.

Hopefully this guide helped you to replace the PCB!

另外一个人完成了本指南。

koppie007

于2013年08月22日注册

1,027 信誉积分

创作了4篇指南

添加评论

浏览统计数据:

Past 24 Hours: 5

Past 7 Days: 70

Past 30 Days: 232

总计 828