跳转到主内容

简介

The LED light on the MiP indicates what mode the robot is in. If this light is malfunctioning, using the MiP is difficult.

  1. Remove the three 12.0 mm Phillips # 2 screws from the battery cover. Remove the three 12.0 mm Phillips # 2 screws from the battery cover.
    • Remove the three 12.0 mm Phillips # 2 screws from the battery cover.

  2. Carefully pull the battery pack from the robot. Remove the batteries from the battery pack.
    • Carefully pull the battery pack from the robot.

    • Remove the batteries from the battery pack.

  3. Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap. This plastic material is not replaceable. Any damage will be noticeable.
    • Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap.

    • This plastic material is not replaceable. Any damage will be noticeable.

  4. Remove the 12.0 mm Phillips #2 screw. Hold the wheel in place, or it will rotate as you attempt to remove the screw.
    • Remove the 12.0 mm Phillips #2 screw.

    • Hold the wheel in place, or it will rotate as you attempt to remove the screw.

  5. Pull the wheel off of the square axle.
    • Pull the wheel off of the square axle.

    • Do not use excessive force while removing the wheel. Pulling too hard on the wheel can damage the axle.

  6. iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    现在开始购物

    iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    现在开始购物
  7. Remove the eight  9.3 mm Phillips #1 screws from the back of the robot. Remove the eight  9.3 mm Phillips #1 screws from the back of the robot.
    • Remove the eight 9.3 mm Phillips #1 screws from the back of the robot.

  8. Remove the arms from the body. Carefully open the body compartment. Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard  could be damaged.
    • Remove the arms from the body.

    • Carefully open the body compartment.

    • Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard could be damaged.

  9. Using precision tweezers, disconnect the following three bundles of wires:
    • Using precision tweezers, disconnect the following three bundles of wires:

    • Connecting the battery pack to the motherboard.

    • Connecting the power switch to the motherboard.

    • Connecting the speaker to the motherboard.

  10. Remove the four 7.5mm Phillips #1 screws. Remove the four 7.5mm Phillips #1 screws.
    • Remove the four 7.5mm Phillips #1 screws.

  11. Carefully pull the motor and motherboard assembly straight out from the base. Be careful not to break the plastic rods that go through the motor assembly and are connect to the shell.
    • Carefully pull the motor and motherboard assembly straight out from the base.

    • Be careful not to break the plastic rods that go through the motor assembly and are connect to the shell.

  12. Use the precision tweezers to unplug the bundle of wires.
    • Use the precision tweezers to unplug the bundle of wires.

  13. Slide the head back to separate it from the body.
    • Slide the head back to separate it from the body.

    • The motherboard does not need to be separated from the head to replace the LED light.

  14. Remove the 7.5mm Phillips #1 screw.
    • Remove the 7.5mm Phillips #1 screw.

    • The LED light is soldered to the small circuit board.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Courtney

于2016年02月04日注册

227 信誉积分

撰写一个指南

团队

USF Tampa, Team 3-4, Wollert Spring 2016 USF Tampa, Team 3-4, Wollert Spring 2016 的会员

USFT-WOLLERT-S16S3G4

4 名成员

创作了5篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 1

总计 409