跳转到主内容
  1. Place CHiP on its back so that its stomach is facing you.
    • Place CHiP on its back so that its stomach is facing you.

  2. There are three small hex screws connecting the battery to CHiP. Remove all screws with a hex screwdriver and remove battery casing. There are three small hex screws connecting the battery to CHiP. Remove all screws with a hex screwdriver and remove battery casing.
    • There are three small hex screws connecting the battery to CHiP. Remove all screws with a hex screwdriver and remove battery casing.

  3. Once the top face of the battery is off, you will see a small rectangular box that the batteries are inside. There are 4 Phillips head screws in the box. Remove all screws with a Phillips head screwdriver. Once the top face of the battery is off, you will see a small rectangular box that the batteries are inside. There are 4 Phillips head screws in the box. Remove all screws with a Phillips head screwdriver.
    • Once the top face of the battery is off, you will see a small rectangular box that the batteries are inside. There are 4 Phillips head screws in the box. Remove all screws with a Phillips head screwdriver.

  4. Once the battery is removed from body, the battery should be connected by a red and black wire. There is a red rectangular connector that easily pulls apart. Pull apart the red rectangular connector. Once the battery is removed from body, the battery should be connected by a red and black wire. There is a red rectangular connector that easily pulls apart. Pull apart the red rectangular connector. Once the battery is removed from body, the battery should be connected by a red and black wire. There is a red rectangular connector that easily pulls apart. Pull apart the red rectangular connector.
    • Once the battery is removed from body, the battery should be connected by a red and black wire. There is a red rectangular connector that easily pulls apart. Pull apart the red rectangular connector.

  5. Remove the 4 Phillips screws shown. Remove the 4 Phillips screws shown.
    • Remove the 4 Phillips screws shown.

  6. Pull up top part of toy and remove the connecting wires. Unscrew the 2 Phillips head screws. CHiP should be viewed as seen in the third picture. Unscrew the 2 Phillips head screws. CHiP should be viewed as seen in the third picture.
    • Pull up top part of toy and remove the connecting wires.

    • Unscrew the 2 Phillips head screws. CHiP should be viewed as seen in the third picture.

  7. Remove the 4 Phillips screws to separate the head from the body. Remove the 4 Phillips screws to separate the head from the body. Remove the 4 Phillips screws to separate the head from the body.
    • Remove the 4 Phillips screws to separate the head from the body.

  8. Remove the 4 Phillips screws on back of the head, and pull off the casing for the back of the head. Remove the 4 Phillips screws on back of the head, and pull off the casing for the back of the head.
    • Remove the 4 Phillips screws on back of the head, and pull off the casing for the back of the head.

  9. Unscrew the screw on the ear with a Phillips screwdriver, and pull off the plastic connector. Remove the ear from head. Unscrew the screw on the ear with a Phillips screwdriver, and pull off the plastic connector. Remove the ear from head. Unscrew the screw on the ear with a Phillips screwdriver, and pull off the plastic connector. Remove the ear from head.
    • Unscrew the screw on the ear with a Phillips screwdriver, and pull off the plastic connector. Remove the ear from head.

结论

To reassemble your device, follow these instructions in reverse order.

Joseph Dantes

于2018年10月02日注册

502 信誉积分

创作了4篇指南

一条评论

It’s almost a disassembly, probably quite hard to do. I did disassemble a MiPosaur, but some parts broke off. (!!!)

Michael Deitz - 回复

添加评论

浏览统计数据:

过去的24小时: 2

过去的7天: 4

过去的30天: 35

总计 882