修复你的物品 社区 商店

VuPoint DC-ST210-VP LCD Screen Replacement

你所需要的

  1. VuPoint DC-ST210-VP LCD Screen Replacement, Turn Off/Remove Batteries: 步骤 1 中的图像 1，1

    • Hold the on/off button for 3 seconds until the screen is black.

    • Remove batteries by placing thumb on battery plate cover sliding it down to expose batteries.

    • Turn camera upside down to allow the batteries to fall out.

    编辑

  2. VuPoint DC-ST210-VP LCD Screen Replacement, Remove Screws: 步骤 2 中的图像 1，3 VuPoint DC-ST210-VP LCD Screen Replacement, Remove Screws: 步骤 2 中的图像 2，3 VuPoint DC-ST210-VP LCD Screen Replacement, Remove Screws: 步骤 2 中的图像 3，3

    • There are 5 (4.5mm in length) screws on the sides of the camera that need to be removed. Use a Phillips #000 screwdriver to remove all screws.

    • Remove 2 screws on the right side of the camera, and store them on a magnetic mat.

    • Remove 2 screws on the bottom of the camera, and store them on a magnetic mat.

    • Remove 1 screw on the left side of the camera, and store it on a magnetic mat.

    编辑

  4. VuPoint DC-ST210-VP LCD Screen Replacement, Pry Backplate Off: 步骤 3 中的图像 1，2 VuPoint DC-ST210-VP LCD Screen Replacement, Pry Backplate Off: 步骤 3 中的图像 2，2

    • Using a prying tool or fingernail, gently separate the back plate from the front plate, exposing the inside of the camera.

    编辑

  5. VuPoint DC-ST210-VP LCD Screen Replacement, Remove Circuit Board Screws: 步骤 4 中的图像 1，1
    在这个步骤中使用的工具：
    Magnetic Project Mat
    $19.95
    购买

    • Using a Phillips #00 screwdriver, remove the 5 (3.5mm in length) screws shown to the left.

    • Remember to place small screws on magnetic mat or in a container.

    编辑

  6. VuPoint DC-ST210-VP LCD Screen Replacement, Seperate Circuit Board: 步骤 5 中的图像 1，3 VuPoint DC-ST210-VP LCD Screen Replacement, Seperate Circuit Board: 步骤 5 中的图像 2，3 VuPoint DC-ST210-VP LCD Screen Replacement, Seperate Circuit Board: 步骤 5 中的图像 3，3

    • Using a pry tool or fingernail, gently pry the circuit board from the base.

    • Gently lift the lower right hand corner of the circuit board, separating it from the base.

    编辑

  7. VuPoint DC-ST210-VP LCD Screen Replacement, Remove LCD from Connector: 步骤 6 中的图像 1，3 VuPoint DC-ST210-VP LCD Screen Replacement, Remove LCD from Connector: 步骤 6 中的图像 2，3 VuPoint DC-ST210-VP LCD Screen Replacement, Remove LCD from Connector: 步骤 6 中的图像 3，3

    • Locate LCD and gently bend it back to reveal ribbon cable connector.

    • Using small screw driver or tweezers gently slide the edges of the ribbon lock towards the direction of the cable.

    • Once the lock is opened, use tweezers to slide the ribbon cable from the connector.

    • Replace LCD as needed and repeat steps in reverse to reassemble.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与3其他贡献者

Lincoln Thompson

于10/20/14注册

32 声望

创作了2篇指南

徽章: 6

+ 3更多徽章

团队

Baylor, Team 8-15, Williams Fall 2014 Baylor, Team 8-15, Williams Fall 2014 的会员

BU-WILLIAMS-F14S8G15

3 名成员

创作了5篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 382