跳转到主内容

简介

You no longer get sound from the speakers on your tablet. This guide will help you gain access to the speaker on your tablet for removal or replacement.

  1. Turn your device to where the back panel is facing you.
    • Turn your device to where the back panel is facing you.

  2. Lift the Leg all the way up and twist the bottom to remove. Once the bottom part pops out the whole leg should just come off.
    • Lift the Leg all the way up and twist the bottom to remove.

    • Once the bottom part pops out the whole leg should just come off.

    • Remove any game cartridge from the device.

  3. Remove all of the plastic tabs on the device. These are covering screws that will need to be removed. These covers are made of hard plastic so they may be difficult to remove. There is a special tab in the cartridge cover that is made of rubber, make sure to not break this tab.
    • Remove all of the plastic tabs on the device. These are covering screws that will need to be removed.

    • These covers are made of hard plastic so they may be difficult to remove.

    • There is a special tab in the cartridge cover that is made of rubber, make sure to not break this tab.

  4. Remove all nine screws from the back of the device using a J0 bit. Remove the small battery.
    • Remove all nine screws from the back of the device using a J0 bit.

    • Remove the small battery.

  5. Using a plastic opening tool, detach the backplate from the front piece. Do not use excessive force. Double check that you removed all the screws if the panel is not coming off easily.
    • Using a plastic opening tool, detach the backplate from the front piece.

    • Do not use excessive force. Double check that you removed all the screws if the panel is not coming off easily.

    • Once the backplate has been removed, you will have access to the circuit board.

  6. Macbook 电池维修套装

    起价 $69.99

    Buy Now

    Macbook 电池维修套装

    起价 $69.99

    Buy Now
  7. First begin by removing the three cross-head screws using a J0 bit.
    • First begin by removing the three cross-head screws using a J0 bit.

  8. First  remove the ribbon cables. There are two highlighted by the red squares
    • First remove the ribbon cables. There are two highlighted by the red squares

    • Do not apply too much pressure and make sure that the black plastic tabs are fully open before you pull the cable out.

  9. Remove the camera from the assembly and put is a safe place so that it will not get damaged.
    • Remove the camera from the assembly and put is a safe place so that it will not get damaged.

  10. Remove the board from the main assembly.
    • Remove the board from the main assembly.

    • Be careful not to pull too hard so that the cables aren't broken.

  11. De-solder the points shown to fully remove the cables and free the board.
    • De-solder the points shown to fully remove the cables and free the board.

    • A soldering guide offered by IFIXIT can be found here Soldering Skills.

  12. Desolder these two points from the circuit board.
    • Desolder these two points from the circuit board.

    • A soldering guide provided by iFixit can be found here: Soldering Skills.

  13. Remove the two screws that are holding down the speaker.
    • Remove the two screws that are holding down the speaker.

  14. Desolder the two wires that are connected to the speaker.
    • Desolder the two wires that are connected to the speaker.

    • A soldering guide offered by IFIXIT can be found here: Soldering Skills.

结论

To reassemble your device, follow these instructions in reverse order.

Esthevan Romeiro

于2016年10月06日注册

261 信誉积分

创作了4篇指南

团队

USF Tampa, Team 5-1, Lacy Fall 2016 USF Tampa, Team 5-1, Lacy Fall 2016 的会员

USFT-LACY-F16S5G1

4 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 4

总计 91