简介

Use this guide to replace the keyboard in your Toshiba Satellite L305-S5946. Unresponsive or sticky keys are good indicators that the keyboard should be replaced. You must remove the keyboard to access the base housing.

Turn the laptop upside-down.
  • Turn the laptop upside-down.

  • Position the laptop so that the display hinges are facing away from you.

添加评论

Slide the left battery bay latch to the left.
  • Slide the left battery bay latch to the left.

添加评论

Slide the right battery bay latch to the right and hold. While holding onto the latch, use a plastic opening tool to lift and remove the battery bay cover. Remove the battery.
  • Slide the right battery bay latch to the right and hold.

  • While holding onto the latch, use a plastic opening tool to lift and remove the battery bay cover.

  • Remove the battery.

添加评论

Use a Phillips #1 screwdriver to loosen the two screws on the bottom left-hand side of the hard drive cover.
  • Use a Phillips #1 screwdriver to loosen the two screws on the bottom left-hand side of the hard drive cover.

  • Turn each screw until you hear a click.

    • These are captive panel screws and remain with the cover.

添加评论

Lift the hard drive cover using a non-marring plastic opening tool. This will expose the hard drive.
  • Lift the hard drive cover using a non-marring plastic opening tool.

    • This will expose the hard drive.

添加评论

Slide the hard drive to the left using your fingers. Insert a plastic opening tool under the right side of the hard drive. Carefully lift and remove the hard drive.
  • Slide the hard drive to the left using your fingers.

  • Insert a plastic opening tool under the right side of the hard drive.

  • Carefully lift and remove the hard drive.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Use a Phillips #1 screwdriver to turn the screw on the RAM cover.
  • Use a Phillips #1 screwdriver to turn the screw on the RAM cover.

  • Turn the screw until you hear a click.

    • This is a captive panel screw and remains with the cover.

添加评论

Insert the plastic opening tool into the indent and lift to remove the RAM cover. This is a captive panel screw and remains with the cover.
  • Insert the plastic opening tool into the indent and lift to remove the RAM cover.

    • This is a captive panel screw and remains with the cover.

添加评论

Use your fingernails to push the white and silver retaining clips away from each side of the RAM card. The RAM card should pop up at an angle.
  • Use your fingernails to push the white and silver retaining clips away from each side of the RAM card.

    • The RAM card should pop up at an angle.

添加评论

Use your fingers to gently pull the RAM card away from the computer. Repeat step 9 to remove the other RAM card that may be installed.
  • Use your fingers to gently pull the RAM card away from the computer.

  • Repeat step 9 to remove the other RAM card that may be installed.

添加评论

Turn the laptop right-side up.
  • Turn the laptop right-side up.

  • Lift open the laptop so that the screen faces you.

添加评论

Remove the strip of plastic at the right furthermost edge of the keyboard using a plastic opening tool. Insert the plastic opening tool at either end of the strip. Lift upwards and proceed to the other end while repeating this lifting process every one to two inches. Insert the plastic opening tool at either end of the strip. Lift upwards and proceed to the other end while repeating this lifting process every one to two inches.
  • Remove the strip of plastic at the right furthermost edge of the keyboard using a plastic opening tool.

  • Insert the plastic opening tool at either end of the strip. Lift upwards and proceed to the other end while repeating this lifting process every one to two inches.

添加评论

Use a Philips #00 screwdriver to loosen and remove the two 3-mm screws at the top edge of the keyboard.
  • Use a Philips #00 screwdriver to loosen and remove the two 3-mm screws at the top edge of the keyboard.

    • These are not captive panel screws and, once loosened, will be free to move about the assembly.

    • Be careful not to allow either fastener into the CPU fan and duct (not shown).

添加评论

Use a plastic opening tool to pry the top of the keyboard loose from its casing. Use a plastic opening tool to pry the top of the keyboard loose from its casing.
  • Use a plastic opening tool to pry the top of the keyboard loose from its casing.

添加评论

Gently grasp the top of the keyboard. Pull it up and toward the screen.
  • Gently grasp the top of the keyboard. Pull it up and toward the screen.

  • Avoid pulling hard and damaging the black ribbon cable under the keyboard.

添加评论

Gently push the two tabs locking the black ribbon cable. Slide the keyboard toward the screen to remove the black ribbon cable from the motherboard. You may now safely separate the keyboard from the laptop.
  • Gently push the two tabs locking the black ribbon cable.

  • Slide the keyboard toward the screen to remove the black ribbon cable from the motherboard.

  • You may now safely separate the keyboard from the laptop.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Michael Erberich

于2013年04月17日注册

100 信誉积分

创作了9篇指南

团队

Cal Poly, Team 3-49, Amido Spring 2013 Cal Poly, Team 3-49, Amido Spring 2013 的会员

CPSU-AMIDO-S13S3G49

4 名成员

创作了10篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 2

总计 1,247