修复你的物品

维修的权力

商店

Toshiba SD-K740 Inverter Board Replacement

撰写者： Joe Murphy (和另外6个贡献者)
  • 评论： 0
  • 收藏 0

难度

中等

步骤

14

所需时间

10 - 15 分钟

节

3

标志

0

简介

This guide gives instructions on how to remove the Right-Side Motherboard (Yellow) of the Toshiba SD-K740 DVD player, which controls the buttons and power function.

工具

购买这些工具

配件

没有特定配件。

  1. Make sure the DVD player is unplugged before beginning.

    • Make sure the DVD player is unplugged before beginning.

    • Remove the three .303 inch screws from the back panel using a Phillips #0 screwdriver.

    编辑

  2. Turn the DVD player on its side. Remove the .303 inch screw.

    • Turn the DVD player on its side.

    • Remove the .303 inch screw.

    • Now flip the DVD player onto its other side.

    • Remove the .303 inch screw from this side.

    编辑

  3. Flip the DVD player over onto its front face.

    • Flip the DVD player over onto its front face.

    • Remove the back panel by lifting up and pulling it towards yourself.

    编辑

  4. Flip the DVD player so its top is sitting on your working surface.

    • Flip the DVD player so its top is sitting on your working surface.

    • Lift and push away each of the two tabs located in the middle of the player.

    • The front panel will not come off during this step, so do not force it.

    编辑

  5. Flip the DVD player on its side.

    • Flip the DVD player on its side.

    • Lift and slide forward a single tab on the side.

    • The front panel will not come off during this step, so do not force it.

    编辑

  7. Grasp the front panel and pull forward and to your right to remove. Grasp the front panel and pull forward and to your right to remove.

    • Grasp the front panel and pull forward and to your right to remove.

    编辑

  8. Remove the black tie holding the two rear ribbon cables together by untwisting it.

    • Remove the black tie holding the two rear ribbon cables together by untwisting it.

    编辑

  9. Remove the first of two ribbon cables connected to the motherboard by pulling vertically. Remove the first of two ribbon cables connected to the motherboard by pulling vertically.

    • Remove the first of two ribbon cables connected to the motherboard by pulling vertically.

    编辑

  10. Remove the second of two ribbon cables connected to the motherboard by pulling vertically. Remove the second of two ribbon cables connected to the motherboard by pulling vertically.

    • Remove the second of two ribbon cables connected to the motherboard by pulling vertically.

    编辑

  11. Pull the two cables to the right to disentangle from the disc drive.

    • Pull the two cables to the right to disentangle from the disc drive.

    • Do not tug, pull, or force cable, it should slide out with minimal force.

    编辑

  12. Pull power cord vertically to detach from the casing.

    • Pull power cord vertically to detach from the casing.

    编辑

  13. Remove the three .303 inch screws attaching the inverter board to the casing using a #0 Phillips screwdriver.

    • Remove the three .303 inch screws attaching the inverter board to the casing using a #0 Phillips screwdriver.

    编辑

  14. Push the inverter board forward and to the left to remove from the holding ledges.

    • Push the inverter board forward and to the left to remove from the holding ledges.

    编辑

  15. Lift the inverter board from the back end and pull toward you to complete removal. Lift the inverter board from the back end and pull toward you to complete removal.

    • Lift the inverter board from the back end and pull toward you to complete removal.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与6其他贡献者

Joe Murphy

于2011年01月20日注册

542 信誉积分

创作了5篇指南

徽章: 10

+ 7更多徽章

团队

Cal Poly, Team 1-16, Amido Winter 2011 Cal Poly, Team 1-16, Amido Winter 2011 的会员

CPSU-AMIDO-W11S1G16

4 名成员

创作了8篇指南

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 1

过去的30天： 4

总计 1,981