跳转到主内容

简介

This guide will go through the steps needed to install a new LCD panel. It's a fairly quick procedure, but it does require some care as it involves very delicate components and short wires that aren't immediately visible. This should be a fairly easy repair if you take it slowly and don't move anything around too roughly—displays are delicate components! Good luck!

  1. Turn the computer over onto its back.
    • Turn the computer over onto its back.

  2. Slide the lock on the left side to the unlock position. Slide the lock on the right side to the unlock position until there is a clicking sound.
    • Slide the lock on the left side to the unlock position.

    • Slide the lock on the right side to the unlock position until there is a clicking sound.

  3. Remove the battery by sliding it out while both locks remain in the unlock position. Remove the battery by sliding it out while both locks remain in the unlock position.
    • Remove the battery by sliding it out while both locks remain in the unlock position.

  4. Use a plastic opening tool to unsnap the right hand side speaker cover. Use a plastic opening tool to unsnap the right hand side speaker cover.
    • Use a plastic opening tool to unsnap the right hand side speaker cover.

  5. iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    现在开始购物

    iPhone X Fix Kits

    Warranty up? No worries, we’ve got the fix.

    现在开始购物
  6. Remove the rest of the cover by sliding it to the right and lifting the right edge. Remove the rest of the cover by sliding it to the right and lifting the right edge.
    • Remove the rest of the cover by sliding it to the right and lifting the right edge.

  7. Remove all eight plastic circular covers on the plastic screen bezel. Only seven of these plastic covers will contain screws underneath.
    • Remove all eight plastic circular covers on the plastic screen bezel.

    • Only seven of these plastic covers will contain screws underneath.

    • Unscrew all seven screws with a Phillips head #000 screwdriver.

  8. Use a plastic opening tool to separate the screen bezel from the rest of the case. Pull at the top edge of the LCD to separate it from the top part of the case.
    • Use a plastic opening tool to separate the screen bezel from the rest of the case.

    • Pull at the top edge of the LCD to separate it from the top part of the case.

    • Only separate the casing and the LCD by an inch—there are still wires connecting them.

  9. Use a Phillips #000 to unscrew the one 2.8 mm fine thread screw holding the wire connected to the right face of the LCD. Use a Phillips #000 to unscrew the one 2.8 mm fine thread screw holding the wire connected to the right face of the LCD.
    • Use a Phillips #000 to unscrew the one 2.8 mm fine thread screw holding the wire connected to the right face of the LCD.

  10. Flip the LCD over onto the back.
    • Flip the LCD over onto the back.

    • Gently pull the connection on the corner of the LCD to disconnect.

  11. Remove the tape connecting LCD to the inverter. Use tweezers to remove the LCD cable from the inverter.
    • Remove the tape connecting LCD to the inverter.

    • Use tweezers to remove the LCD cable from the inverter.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Alison Wendt

于2013年04月18日注册

78 信誉积分

创作了6篇指南

团队

Cal Poly, Team 21-51, Johann Spring 2013 Cal Poly, Team 21-51, Johann Spring 2013 的会员

CPSU-JOHANN-S13S21G51

3 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 1

过去的30天: 4

总计 703