修复你的物品 社区 商店

当前版本的文档还未经巡查，您可以查看最新的已查核版本。

你所需要的

  1. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 1 中的图像 1，3 : 步骤 1 中的图像 2，3 : 步骤 1 中的图像 3，3

    • To get to the screws beneath the keyboard you need to take some keys off. You can use either an opening tool or an opening pick. The first picture shows how it should look like with all the necessary keys off (12 in total).

    • The four longer keys from the fingerboard are to be handled from the left side to get them off.

    • The eight smaller keys need to be levered from the bottom up.

    翻译

  2. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 2 中的图像 1，2 : 步骤 2 中的图像 2，2

    • The scissor mechanism of the eight small keys are obstructing the underlying screws.

    • By using again an opening tool or opening pick these can be snapped off easily.

    • When reassembling be sure to place them in with the correct side facing upwards.

    翻译

  3. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 3 中的图像 1，3 : 步骤 3 中的图像 2，3 : 步骤 3 中的图像 3，3

    • Loosen those 12 screws with a Phillips #00 screwdriver.

    • Then just pull off the four rotary knobs and the volume knob.

    • Now it is possible to slightly lift the keyboard and set it back.

    翻译

  5. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 4 中的图像 1，1

    • Unlock the flex cables by pushing the two black nibs on both sides of each connector.

    • Now you can pull the flex cables out and remove the keyboard completely.

    翻译

  6. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 5 中的图像 1，3 : 步骤 5 中的图像 2，3 : 步骤 5 中的图像 3，3

    • Open the display cable connector by using a plastic opening tool to flip the latch upwards.

    • The display is held in place with a mild adhesive. A spudger helps you to get it free.

    • Now you can unplug the cable and take out the whole display.

    翻译

  7. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 6 中的图像 1，2 : 步骤 6 中的图像 2，2

    • Disconnect the battery connector from the DSP board.

    • Unscrew the two Phillips #00 screws holding the board down.

    翻译

  8. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 7 中的图像 1，2 : 步骤 7 中的图像 2，2

    • Now you can carefully lift the DSP board to access the flex cable connector underneath.

    • Disconnect the flex cable by using a spudger and remove the DSP board.

    翻译
终点

4等其他人完成本指南。

作者

Tobias Isakeit

于03/31/14注册

117,504 声望

创作了188篇指南

徽章: 46

+ 43更多徽章

团队

Master Techs Master Techs 的会员

Community

322 名成员

创作了2,528篇指南

13条评论

Can you advise me where I can order DSP board?

Ju-seok Jang - 回复

Hi Ju-seok Jang, unfortunately we don’t sell this spare part. You might be able to reach Teenage Engineering directly and get an answer from them where to purchase that part.

Tobias Isakeit -

I reached out to teenage engineering a month ago about ordering a replacement but they still haven’t responded. Pretty unacceptable seeing as they have a “do it yourself!” ethos for their $1,000 device…

Ben Fischer - 回复

Hi! Did you find a solution? I have the same issue. Thanks!

Juan Rodríguez Berbín -

My OP-1 wouldn’t go into boot mode, and TE told me it was probably the DSP board, and they would look at it for a fee since it was out of warranty. Now I can’t find the DSP board anywhere to do this repair. I then found out this was a common problem, a manufacturing defect. I wonder if there are enough people with these problems the EU 2 year warranty rule can be invoked, or a class-action suit of some sort. TE has basically left those who have these problems without an option to repair the TE manufacturing defect.

Rob

Robert Herman - 回复

添加评论

浏览统计数据:

过去 24 小时： 2

过去 7 天： 28

过去 30 天： 130

总计 11,613