跳转到主内容

Swagtron T3 Gyroscope Replacement

你所需要的

  1. Swagtron T3 Gyroscope Replacement, Cover: 步骤 1 中的图像 1,2 Swagtron T3 Gyroscope Replacement, Cover: 步骤 1 中的图像 2,2
    • Make sure the hoverboard is completely powered off and unplugged from any outlets.

    • Flip the Swagtron so that the footpads are facing the ground.

    • Unscrew the sixteen 9.4 mm Phillips #1 machine screws on the side of the Swagtron that is now facing upwards.

  2. Swagtron T3 Gyroscope Replacement: 步骤 2 中的图像 1,3 Swagtron T3 Gyroscope Replacement: 步骤 2 中的图像 2,3 Swagtron T3 Gyroscope Replacement: 步骤 2 中的图像 3,3
    • Be careful with the small blue capacitors indicated by the orange box. There are many of these capacitors in the device.

    • Slowly lift the backside cover.

    • Both sides lift up the same way, but the motherboard is under one side and the battery is under the other.

    • Detach the four cables connected to the cover by pinching the connector clips and pulling the cables out:

    • Three cables on the motherboard side.

    • Two red cables with white connectors and one white cable with a white connector.

    • One yellow cable with a black connector on the battery side.

    • After detachment, you should be able to completely remove the backside cover.

  3. Swagtron T3 Gyroscope Replacement, Gyroscope: 步骤 3 中的图像 1,1
    • The gyroscope is a blue rectangular circuit board on top of a white base and is closest to the wheel.

    • Detach the four cables connecting the gyroscope to the hoverboard by pinching the connector clips and pulling the cables out:

    • Three red and black cables with white connectors.

    • One multicolored cable with a black connector.

  4. Swagtron T3 Gyroscope Replacement: 步骤 4 中的图像 1,1
    • Uncrew the four 7.2 mm Phillips #1 self-drilling screws connecting the blue gyroscope to the white plastic holding piece.

  5. Swagtron T3 Gyroscope Replacement: 步骤 5 中的图像 1,2 Swagtron T3 Gyroscope Replacement: 步骤 5 中的图像 2,2
    • Cut the plastic cable tie holding the cables together with utility scissors.

    • Disconnect the blue/green cable from the blue/white cable by pinching the connector clips and pulling the cables apart.

  6. Swagtron T3 Gyroscope Replacement: 步骤 6 中的图像 1,1
    • Gently lift the blue gyroscope off of the white plastic holder piece.

    • After reassembling the Swagtron with the new gyroscope, check to make sure your Swagtron is balancing properly.

    • If it is still unbalanced, repeat all steps in this guide with the gyroscope by the other wheel.

结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

Emily Richter

于04/10/17注册

351 声望

撰写一个指南

团队

Cal Poly, Team S13-G3, Forte Spring 2017 Cal Poly, Team S13-G3, Forte Spring 2017 的会员

CPSU-FORTE-S17S13G3

4 名成员

创作了4篇指南

3条评论

Where can one buy the new gyroscope?

Mike - 回复

Where is the best place to buy the gyroscope for the T3?

I see Ebay sells complete kits with motherboards and all.

Are they compatible?

Mike - 回复

where can I buy new gyroscope

roccovalletta - 回复

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 4

过去 30 天: 29

总计 4,828