简介

This guide give instructions on how to locate the speaker for removal and/or repair.

  1. Flip over the phone and then slide down the back cover with your thumb.
    • Flip over the phone and then slide down the back cover with your thumb.

  2. Lever out the battery from the phone using your thumb.
    • Lever out the battery from the phone using your thumb.

  3. With the phone closed, run a plastic opening tool along the seam of the top half of the phone Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top) Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top)
    • With the phone closed, run a plastic opening tool along the seam of the top half of the phone

    • Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top)

  4. Using T6 Torx Screwdriver, remove the four 3.16mm screws from the front panel Note that the fourth screw is under a fold in the ribbon cable
    • Using T6 Torx Screwdriver, remove the four 3.16mm screws from the front panel

    • Note that the fourth screw is under a fold in the ribbon cable

  5. 所有超过US$100或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店
  6. Starting in the lower right corner, slowly start to lift the tape that is holding the front LCD and cables down Be careful around the two ribbon cables that are attached to the tape, they are fragile Lift the tape from the board
    • Starting in the lower right corner, slowly start to lift the tape that is holding the front LCD and cables down

    • Be careful around the two ribbon cables that are attached to the tape, they are fragile

    • Lift the tape from the board

  7. Using a plastic opening tool, lift the ribbon cable connection below the front LCD
    • Using a plastic opening tool, lift the ribbon cable connection below the front LCD

  8. Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board
    • Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board

  9. Locate the ribbon cable connection in the upper right hand corner of the board
    • Locate the ribbon cable connection in the upper right hand corner of the board

    • Using a plastic opening tool, lift off the cable from the board

    • Be gentle and make sure not to rip the ribbon cable

  10. Using a plastic opening tool, slowly work the board off the mounts holding it to the frame Flip the board over to reveal the main display
    • Using a plastic opening tool, slowly work the board off the mounts holding it to the frame

    • Flip the board over to reveal the main display

  11. Locate the ribbon cable for the main display on the bottom of the board
    • Locate the ribbon cable for the main display on the bottom of the board

    • Slowly lift off the ribbon connector from its housing using a plastic opening tool

  12. Slowly wedge the plastic opening tool under the bottom of the main display Separate the display from the glue lifting it off the board
    • Slowly wedge the plastic opening tool under the bottom of the main display

    • Separate the display from the glue lifting it off the board

  13. Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.
    • Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

结论

To reassemble your device, follow these instructions in reverse order.

Andrew

于2010年10月04日注册

361 信誉积分

创作了4篇指南

团队

Cal Poly, Team 4-46, Amido Fall 2010 Cal Poly, Team 4-46, Amido Fall 2010 的会员

CPSU-AMIDO-F10S4G46

4 名成员

创作了14篇指南

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 1

总计 429