简介

How to remove the Logic Board from the Sony Vaio VGN-S260 laptop

  1. Flip the laptop over so the Vaio logo is facing down
    • Flip the laptop over so the Vaio logo is facing down

    • Locate the battery at the top and Find the release and unlock slides on the battery

    • Slide the unlock tab to the unlock position

    • Slide the release tab in the direction of the arrow, i.e. towards the unlock tab

    添加评论

  2. With the tabs still in the unlock position, slide the battery away from the main case.
    • With the tabs still in the unlock position, slide the battery away from the main case.

    添加评论

    • Flip the computer over so the Vaio logo is facedown

    • Unscrew the 2 screws next to the battery

    添加评论

    • Flip the computer over again so the Vaio logo is face up

    • Open the lid

    添加评论

    • Press down on the outer gray shell around the keyboard

    • Use the spudger to gently lift keyboard

    • Do not pull up the keyboard too far as it is attached to a ribbon underneath

    There are 2 spring-held latches, one above the F4 and one above the F12. Push a latch up into the frame of the keyboard, then lift the keyboard gently in that area so the latch doesn't spring back. Then push the other latch and the keyboard will be released.

    Yishai Sered - 回复

    • Lift up lever underneath the ribbon to detach the keyboard.

    添加评论

    • Remove memory/wireless compartment cover

    添加评论

    • Flip so the Vaio Logo is face down

    • Locate and remove a total of 8 screws on the bottom.

    There are 2 more screws on the bottom, one in the middle of the front next to the flash stick socket, and one under the memory door.

    Yishai Sered - 回复

    • Find and remove 5 screws (they all have arrows next to them) from cover

    添加评论

    • Flip the laptop over so the Vaio logo is face up

    • Use the spudger to pop up the upper casing

    • Do not lift too much as the Uppercasing is attached to wires underneath

    • Remove the wires that are attaching the uppercasing to the motherboard

    There are also 5 screws from the top of the uppercasing.

    Yishai Sered - 回复

    The are 4 cables to remove: flat cable for the power and S buttons at top center; flat cable for the touchpad at bottom center; and 2 twisted pairs for the speakers.

    The speaker cable socket is very delicate. If all you are getting at is the CPU or the hard drive, it may be enough to disconnect the flat cables and gently rotate the uppercasing shifting it left to allow access to the right-hand side with the CPU fan and the hard drive.

    Yishai Sered - 回复

    The top panel has cutouts that allow the cables to be disconnected before the top of the case is removed. The two flat cables are not clamped and can be pulled vertically out of their connectors. The delicate speaker cables are connected to the motherboard with plugs which can be gently levered up out of their sockets.

    roberttrevellyan - 回复

    • Remove the uppercasing

    添加评论

    • Locate the yellow power adapter

    • Follow its wire to white logic board connector

    • Pull out the wire from white logic board connector

    添加评论

    • Locate the screws on the fan filter casing

    • Remove these screws

    添加评论

    • Remove the screw next to the yellow power adapter

    • Lift out power adapter and fan filter

    添加评论

    • Locate the screw holding the optical drive casing to the logic board

    • Remove this screw

    This screw is from the bottom, will not be there since you removed it to get the uppercasing.

    Yishai Sered - 回复

    However, there is a screw on the bottom right of the PC-CARD cage to remove.

    Yishai Sered - 回复

    • Locate ribbon connecting optical drive case to logic board.

    • Pop off the ribbon

    • Remove the metal PC-Card cage

    添加评论

    • Locate the four screws holding the optical drive to the logic board

    • Remove the screws

    添加评论

    • Locate brown locking tab above optical drive.

    • Lift up on brown locking tab until ribbon is loose

    • Gently slide out and remove the optical drive from the computer

    添加评论

    • Remove the blue ribbon from the Ethernet Circuit Board

    添加评论

    • Locate the screws near the Ethernet Port circuit board

    • Remove the screws.

    添加评论

    • Locate the screws for the second ethernet circuit board

    • Remove the screws

    添加评论

    • Remove the ethernet ports

    添加评论

    • Locate the screws holding the hard drive casing in place.

    • Remove the screws

    Only the 2 bottom red circles have screws. The top two are open holes for screws that come in from the bottom.

    Yishai Sered - 回复

    Only the two bottom screws are there. The two top screws are from the bottom and would have been removed to get the uppercasing off.

    Yishai Sered - 回复

    • Find orange ribbon that is connected to the hard drive.

    • Find the holder of the ribbon and pop the ribbon off from it

    添加评论

    • Remove the casing and the orange ribbon

    添加评论

    • Locate screws on the logic board

    • Remove the screws

    添加评论

    • Locate nut on logic board

    • Take out the nut using the 5mm nut driver

    • Using a magnetic screwdriver handle will also work as well

    添加评论

    • Remove the LCD display ribbon

    • It is helpful to use the spudger here

    • This is difficult to remove

    添加评论

    • Gently lift the logic board from the laptop.

    • The logic board will be attached to the network wireless chip, which is also attached to the base of the laptop

    • Remove the chip by poping the tabs on the side

    • Slide out the network card

    • You are now free to take the logic board away from the base

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Jeffrey Bryan

于2010年04月20日注册

552 信誉积分

创作了11篇指南

团队

Cal Poly, Team 16-4, Maness Spring 2010 Cal Poly, Team 16-4, Maness Spring 2010 的会员

CPSU-MANESS-S10S16G4

4 名成员

创作了11篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 7

总计 6,602