简介

This guide will inform readers on how to safely uninstall the keyboard of the Sony VAIO VPC-EB33FM laptop.

配件

无需配件。

If the laptop isn't turned off, then do so by holding down the power button.
  • If the laptop isn't turned off, then do so by holding down the power button.

  • Turn the laptop onto its backside.

添加评论

Locate the battery below the screen attachment.
  • Locate the battery below the screen attachment.

  • The battery is shaped as a long rectangle with rounded edges.

添加评论

  • Press into the release button while holding the unlock button in position.

添加评论

  • Lift the battery out at the notch while holding the release button.

添加评论

  • Remove all charge from the laptop by holding down the power button for at least 5 seconds.

添加评论

  • Turn laptop onto its backside and locate the hard drive cover panel.

添加评论

  • Use a Phillips #00 screwdriver to remove the two 7.75-mm cover screws on the bottom corners of the panel.

添加评论

  • Use a finger/fingernail to grip the notch at the bottom of the panel to lift it off.

  • You may need to use your other hand to safely remove the panel.

  • You can also use a spudger for this step

添加评论

  • The hard drive should now be exposed.

  • Remove the two remaining 7.75-mm screws using the Phillips #00 screwdriver.

添加评论

  • Grab the tab between your thumb and index finger.

  • Hold the hard drive securely in a horizontal position using your other hand.

  • Push the hard drive to the left using the plastic tab to disconnect it from the laptop.

  • To prevent damage of the connection on the hard disk drive or the laptop, perform this task slowly and with care.

添加评论

  • While still holding the plastic tab, lift the right side of the hard drive out at a 45º angle.

  • Pull the hard drive out.

添加评论

  • If you need to remove the bracket from the hard drive, follow the next few steps:

    • Remove the two 3.67-mm screws from either side of the bracket with a Phillips #00 screwdriver.

    • Lift the bracket off the hard drive.

添加评论

  • Remove the one screw with a Phillips #00 screwdriver.

  • The screw cannot be removed from the RAM casing cover.

添加评论

  • Pull the two retaining arms away from the center of the RAM chip.

  • The RAM will make a "pop" sound and the RAM stick will rise for ease of handling.

添加评论

  • Pull the RAM stick out of its socket.

  • To remove the second stick of RAM, repeat steps six and seven.

  • When installing RAM, make sure sticks are firmly in place or the computer will not register them.

添加评论

  • Using a Phillips #00 screwdriver remove the following screws securing the back cover :

    • Two 3.8-mm screws

    • Two 8.9-mm screws

    • Twelve 7.75-mm screws

添加评论

  • Check to make sure all screws have been removed.

  • Using both hands separate the back cover by lifting from the back and working around the perimeter to release tabs.

添加评论

  • Uninstalling the keyboard may require a second set of hands.

  • During the removal of the back cover, a screw that attaches the optical drive to the laptop is also taken out. This means the optical drive is ready to be removed.

  • Remove the optical drive by sliding it out.

添加评论

  • Once the optical drive is removed, locate the keyboard ejection button and press down on it until you hear a snap.

  • Once you hear this sound, it means that a section of the keyboard has been ejected.

添加评论

  • Turn the laptop onto its frontside and unfold the laptop so the keyboard is fully visible.

  • Locate the area where the section of the keyboard was ejected.

添加评论

  • Start to pry out the keyboard with your hands.

  • Be careful not to break any of the hooks that attach the keyboard to the laptop.

  • If it seems difficult to remove the keyboard with your hands, then use a plastic opening tool.

添加评论

  • Remain cautious to not break the hooks.

  • Continue all the way around the keyboard until you can detach it from the laptop.

添加评论

  • Do not immediately pull the keyboard away from the laptop. There is still an attachment between the keyboard and laptop.

  • Turn the keyboard on its face and locate the green tape and the ribbon attachment.

  • Using the metal tweezer, remove only the green sticker.

  • Place the sticker at any location as long as you remember to use it for installing the keyboard.

添加评论

  • Locate the black retaining arms.

  • Using the plastic opening tool, pull the retaining arms out.

  • The retaining arms will not come off completely.

添加评论

  • It is safe to touch the ribbon attachment.

  • Lift the retaining arms with the plastic opening tool at an angle so that the ribbon attachment can be pulled out.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

10等其他人完成本指南。

Kevin

于2013年01月11日注册

478 信誉积分

创作了3篇指南

团队

Cal Poly, Team 18-39, Regan Winter 2013 Cal Poly, Team 18-39, Regan Winter 2013 的会员

CPSU-REGAN-W13S18G39

5 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 5

过去的7天: 30

过去的30天: 185

总计 15,513