修复你的物品 社区 商店

本指南有最近更改，您可查看未经巡查的最新版本。

Sony SRS-X3 Speakers Replacement

简介

On this guide, the aim is to teach how to disassemble the Sony SRS-X3 bluetooth speaker in order to replace the speakers in the unit. This teardown is fairly simple, and only requires two tools. This speaker replacement is being completed because of a humming sound coming from the unit when music is being played.

你所需要的

  1. Sony SRS-X3 Speakers Replacement, Speakers: 步骤 1 中的图像 1，1

    • Remove rubber feet on the bottom of the device

    翻译

  2. Sony SRS-X3 Speakers Replacement: 步骤 2 中的图像 1，1

    • Remove 6 silver philips head screws with PH1 bit

    • Remove bottom plastic cover of speaker

    翻译

    Hola este yo tengo un parlante asi pero no kiere gargar

    Chrlz Maza Olivera - 回复

  3. Sony SRS-X3 Speakers Replacement: 步骤 3 中的图像 1，1

    • Remove 2 phillips head screws holding battery pack with PH1 bit

    • Remove battery back with spudger

    翻译

  5. Sony SRS-X3 Speakers Replacement: 步骤 4 中的图像 1，1

    • Unscrew 3 phillips head screws using PH1 bit

    • Remove green board. Battery pack and green circuit board should still be connected to the speaker by a ribbon wire. This is normal.

    翻译

  6. Sony SRS-X3 Speakers Replacement: 步骤 5 中的图像 1，2 Sony SRS-X3 Speakers Replacement: 步骤 5 中的图像 2，2

    • Pop off front speaker face (dark grey with little holes) by pushing out 3 tabs where screws were previously located and sticking spudger in crack where grey speaker face meets the outer shell

    • You may really have to pry on this part, it is not easy to remove and will pop out when released

    翻译

  7. Sony SRS-X3 Speakers Replacement: 步骤 6 中的图像 1，1

    • Remove 8 black phillips head screws shown with PH1 bit

    翻译

  8. Sony SRS-X3 Speakers Replacement: 步骤 7 中的图像 1，2 Sony SRS-X3 Speakers Replacement: 步骤 7 中的图像 2，2

    • Remove front face by prying 2 black tabs shown using spudger

    • This face is glued in and may need some elbow grease to remove. Don't worry about breaking anything, as it is all connected

    翻译

  9. Sony SRS-X3 Speakers Replacement: 步骤 8 中的图像 1，1

    • Remove speaker wires from each speaker (2 wires per speaker) and take speakers out of device

    • Speaker wire connectors are made to connect very snug, so they should be hard to remove. Give it a good tug and they should pop off the male end

    翻译

  10. Sony SRS-X3 Speakers Replacement: 步骤 9 中的图像 1，1

    • You can now replace your speakers and reassemble this unit. If replacing the mother board continue with steps 10-14 in the mother board repair guide.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

4条评论

Where would I get the new speakers from tho? Thanks a lot

Ruben Götz - 回复

Where I can buy one speaker as a spare part?

Karim Karimov - 回复

I would also like to know where I can get a replacement speaker

Aaron Todd - 回复

This SRS X3 cannot be used with the dc in 5v plugged, how can i do to make it work continuously with the charge cable? It have to be hacked? thanks

carlos cesar quan - 回复

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 3

过去 30 天： 13

总计 2,436