简介

This guide will allow the user to access the motherboard for installation, replacement, or removal.

The battery cover is located on the right side of the camera.
  • The battery cover is located on the right side of the camera.

  • Slide the cover to expose the battery.

添加评论

Ensure that the battery lines up properly with the slot in the camera.
  • Ensure that the battery lines up properly with the slot in the camera.

  • Slide battery in.

  • Slide cover closed.

  • Battery not shown

添加评论

  • Remove screws from outside of camera. There are 6 screws total.

  • 3 screws on underside.

  • 1 screw on right side, near battery cover.

  • 2 screws on left side.

添加评论

  • Use screwdriver to remove screws.

添加评论

  • Gently pull the front cover off of the main camera.

  • All of the inner parts of the camera are attached to the back screen.

添加评论

  • The front cover is now removed from the camera and the internal hardware is now exposed.

添加评论

  • This is the camera without the front cover.

添加评论

  • Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.

添加评论

  • Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.

添加评论

  • Pull apart the inner hardware from the back case by prying on the left side.

添加评论

  • Remove the back cover.

添加评论

  • The back cover is now removed from the internal hardware.

添加评论

  • Use the spudger to pry the LCD from the camera.

添加评论

  • The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.

添加评论

  • Flip camera to other side.

  • Use tweezers to peel off black sticker, located in middle of the motherboard.

添加评论

  • Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.

添加评论

  • The LCD is now removed from the camera.

添加评论

  • This is the CCD module.

添加评论

  • Use plastic opening tool pop open the two ribbons attaching to the CCD module.

  • These are the two ribbons.

添加评论

  • Remove CCD module.

    • You may have to tug on the ribbons to remove the CCD module.

添加评论

  • The CCD module is now removed from the camera.

添加评论

  • These two screws hold in the AV port.

  • Use Phillips screwdriver to remove screws.

添加评论

  • Remove metal screw plate.

添加评论

  • Use pry stick to pop off ribbon.

添加评论

  • Remove AV port from camera.

添加评论

  • The battery cover is located here.

  • Pull away from camera to remove.

添加评论

  • Grip on the top and bottom.

  • Pull up and out to remove motherboard and attached parts.

添加评论

  • Flip motherboard parts to position shown.

  • There are three ribbons still attached to the motherboard.

  • Pull these three ribbons to remove remaining parts from motherboard.

添加评论

  • The motherboard is now removed from the camera.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

Stephannie Allen

于2013年03月11日注册

189 信誉积分

创作了10篇指南

团队

Clemson, Team 13-1, Benson Spring 2013 Clemson, Team 13-1, Benson Spring 2013 的会员

CLEM-BENSON-S13S13G1

4 名成员

创作了10篇指南

Superb,thank you very much !!!

Vedrasco Victor Vasili - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 1

总计 388