配件

无需配件。

Slide the battery latch down the side of the camera with your hands.
  • Slide the battery latch down the side of the camera with your hands.

  • The latch will automatically pop open.

添加评论

Unlatch the clip over the battery.
  • Unlatch the clip over the battery.

  • The battery will partially pop out.

添加评论

Remove the battery from the camera. Remove the battery from the camera.
  • Remove the battery from the camera.

添加评论

Remove the four 3.0mm Phillips #000 screws on the top of the camera with the phillips screwdriver. Remove the additional four 3.0mm Phillips #000 screws on the bottom of the camera.
  • Remove the four 3.0mm Phillips #000 screws on the top of the camera with the phillips screwdriver.

  • Remove the additional four 3.0mm Phillips #000 screws on the bottom of the camera.

添加评论

Once the screws are removed, slowly remove the back casing from the rest of the camera. Once the screws are removed, slowly remove the back casing from the rest of the camera.
  • Once the screws are removed, slowly remove the back casing from the rest of the camera.

添加评论

Then, pull the front case away from the rest of the camera. Then, pull the front case away from the rest of the camera.
  • Then, pull the front case away from the rest of the camera.

添加评论

After the casing is removed, the camera should look as shown.
  • After the casing is removed, the camera should look as shown.

添加评论

Dislodge the round casing from the lens. Pull it away from the rest of the camera.
  • Dislodge the round casing from the lens.

  • Pull it away from the rest of the camera.

添加评论

Unscrew the two 4.0mm Phillips #000 screws from the display.
  • Unscrew the two 4.0mm Phillips #000 screws from the display.

添加评论

Pull the two ribbon cables out of their slots on the back circuit board.
  • Pull the two ribbon cables out of their slots on the back circuit board.

添加评论

Remove the three 4.0mm Phillips #000 screws holding the back panel in place.
  • Remove the three 4.0mm Phillips #000 screws holding the back panel in place.

添加评论

Work the back panel out from under the small grey clip. Slide the back panel off of the camera by dislodging it from the remaining clips. Below is a flat, orange cable connecting the lens to the motherboard.
  • Work the back panel out from under the small grey clip.

  • Slide the back panel off of the camera by dislodging it from the remaining clips.

  • Below is a flat, orange cable connecting the lens to the motherboard.

  • Be careful not to bend the back plate during this process.

添加评论

Turn the camera over so that you can see the front of the lens.
  • Turn the camera over so that you can see the front of the lens.

  • Two connectors link the lens to the motherboard.

  • Gently bring the lens away from the camera.

添加评论

Using the flat end of the plastic spudger tool, flip up the black tabs on the connectors.
  • Using the flat end of the plastic spudger tool, flip up the black tabs on the connectors.

  • Be careful not to exert too much force, as the connectors are delicate.

添加评论

Gently pull out the cables and move the lens away from the rest of the camera. You should now have two distinct, separate components. You should now have two distinct, separate components.
  • Gently pull out the cables and move the lens away from the rest of the camera.

  • You should now have two distinct, separate components.

添加评论

Remove the 3.0mm Phillips #000 screw at the top of the battery door.
  • Remove the 3.0mm Phillips #000 screw at the top of the battery door.

添加评论

Pull off the top button piece. You will have to detach a small blue ribbon cable. Pull off the top button piece. You will have to detach a small blue ribbon cable.
  • Pull off the top button piece. You will have to detach a small blue ribbon cable.

添加评论

Caution: the capacitor, a black cylinder near the top of the camera, might have a charge in it, which could be harmful to you or the camera. Neutralize it by touching both wires with a screwdriver at the same time. Caution: the capacitor, a black cylinder near the top of the camera, might have a charge in it, which could be harmful to you or the camera. Neutralize it by touching both wires with a screwdriver at the same time.
  • Caution: the capacitor, a black cylinder near the top of the camera, might have a charge in it, which could be harmful to you or the camera. Neutralize it by touching both wires with a screwdriver at the same time.

添加评论

Remove the flash mechanism. It is held in place by a clip on the side of the camera. The capacitor and flash will rotate out, still attached by a ribbon cable on the left. The capacitor and flash will rotate out, still attached by a ribbon cable on the left.
  • Remove the flash mechanism. It is held in place by a clip on the side of the camera.

  • The capacitor and flash will rotate out, still attached by a ribbon cable on the left.

添加评论

Lift up the black tab with the spudger. Gently remove the ribbon cable from the rest of the camera.
  • Lift up the black tab with the spudger.

  • Gently remove the ribbon cable from the rest of the camera.

  • The flash component is now completely separate from the rest of the camera.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Andrew Forster

于2012年04月16日注册

9 信誉积分

创作了2篇指南

团队

Cal Poly, Team 17-25, Amido Spring 2012 Cal Poly, Team 17-25, Amido Spring 2012 的会员

CPSU-AMIDO-S12S17G25

4 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 4

总计 561