修复你的物品 社区 商店

Solio CLASSIC2 Removing the Circuit Board

简介

Removing the circuit board will allow you to more easily solder on the circuit board.

你所需要的

  1. Solio CLASSIC2 Removing the Circuit Board, Disconnecting the Battery: 步骤 1 中的图像 1，1

    • Turn off the device by pressing on the clear power button behind the device.

    • To make sure that it is off, make sure the button is not flashing green.

    编辑

  2. Solio CLASSIC2 Removing the Circuit Board: 步骤 2 中的图像 1，1

    • Using the Phillips #1 screwdriver, remove the 2mm screw located on the bottom of the device, near the hinge.

    编辑

  3. Solio CLASSIC2 Removing the Circuit Board: 步骤 3 中的图像 1，3 Solio CLASSIC2 Removing the Circuit Board: 步骤 3 中的图像 2，3 Solio CLASSIC2 Removing the Circuit Board: 步骤 3 中的图像 3，3

    • Using the plastic opening tools, gently pry open the side of the large panel.

    • Keeping the tool in, slowly slide the tool along the side of the panel.

    编辑

  5. Solio CLASSIC2 Removing the Circuit Board: 步骤 4 中的图像 1，2 Solio CLASSIC2 Removing the Circuit Board: 步骤 4 中的图像 2，2

    • Rotate the device 180 degrees.

    • Make sure the opening on other side of the device does not snap closed.

    • Gently slide the plastic opening tool along the side of the panel.

    编辑

  6. Solio CLASSIC2 Removing the Circuit Board: 步骤 5 中的图像 1，2 Solio CLASSIC2 Removing the Circuit Board: 步骤 5 中的图像 2，2

    • Do not fully pull apart the back panel from the device. Doing so can rip the two red and blue wires attached to the panel.

    • Using both hands, slowly pull apart the back panel from the rest of the device.

    • Gently flip the back panel open so the circuit board faces up and the two panels are side by side.

    编辑

  7. Solio CLASSIC2 Removing the Circuit Board: 步骤 6 中的图像 1，2 Solio CLASSIC2 Removing the Circuit Board: 步骤 6 中的图像 2，2

    • Softly pinch the red and blue wires close to the white connector.

    • To pull the wires out, wiggle them back and forth until the connector is fully out.

    编辑

  8. Solio CLASSIC2 Removing the Circuit Board, Circuit Board: 步骤 7 中的图像 1，1

    • Unscrew the three 2mm screws holding the circuit board down using a Phillips #1 screwdriver.

    编辑

  9. Solio CLASSIC2 Removing the Circuit Board: 步骤 8 中的图像 1，1

    • Make sure the white USB port cover on the side of the device is pulled out or you won't be able to lift the circuit board.

    • Gently lift the circuit board out of the device using tweezers.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与4其他贡献者

Eric Padilla

于10/21/13注册

201 声望

创作了2篇指南

徽章: 3

团队

Cal Poly, Team 4-28, Amido Fall 2013 Cal Poly, Team 4-28, Amido Fall 2013 的会员

CPSU-AMIDO-F13S4G28

4 名成员

创作了7篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 221