Skip to main content

介绍

The XLR Connector is the part of the microphone that plugs into the cable which carries the sound to the sound mixer and speakers.

  1. Using a small flat head screwdriver, gently turn the retaining screw at the bottom of the microphone counterclockwise until it stops or provides resistance.
    • Using a small flat head screwdriver, gently turn the retaining screw at the bottom of the microphone counterclockwise until it stops or provides resistance.

    • The retaining screw is mounted to the connector and has a left-handed thread. Turning the screw clockwise locks the connector in place. Turning it counterclockwise lowers it down into the hole, releasing the connector.

    • Once the screw stops, do not try to loosen it further.

  2. Plug an XLR cable into the loose connector.
    • Plug an XLR cable into the loose connector.

    • While holding the disconnect button down, pull on the cable to remove the connector from the body of the microphone.

  3. If the wire is not exposed from the insulation, strip the broken wire.
    • If the wire is not exposed from the insulation, strip the broken wire.

  4. Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物

    Android 维修工具包

    一个新的屏幕或电池就在一个套件之内。

    现在开始购物
  5. Bend the wire around the contact point. Pin numbers are located on the outside of the connector.
    • Bend the wire around the contact point. Pin numbers are located on the outside of the connector.

    • Connect the red wire to Pin 3 and the blue wire to Pin 2.

    • Pin 1 should have a single piece of exposed wire connecting it to the metal plate on the top of the connector (the ground plate).

  6. Clamps are helpful for this step.
    • Clamps are helpful for this step.

    • In one hand, hold the solder. In the other hold your soldering iron.

    • Touch both the soldering iron and the solder to the contact point. The solder should melt and create a connection between the wire and the microphone connector.

  7. Remove the solder and then the soldering iron from the contact point.
    • Remove the solder and then the soldering iron from the contact point.

    • If you remove the soldering iron first, the solder may become stuck to the contact point.

    • Let the wire cool for 30 seconds or so.

    • If the wire is not completely connected repeat steps 2 through 5.

  8. To reinstall the XLR connector, follow the Installing Shure SM58 XLR connector guide
结论

After soldering the wires to the XLR connector and reassembling your microphone, your microphone should be ready to plug in to the XLR cable and function properly.

3等其他人完成本指南。

nat coll

于2012年09月27日注册

423 Reputation

创作了14篇指南

Team

Cal Poly, Team 7-53, Forte Fall 2012 Cal Poly, Team 7-53, Forte Fall 2012 的会员

CPSU-FORTE-F12S7G53

5 名成员

创作了18篇指南

7 Comments

Many thanks. Very helpful.

Namron - 回复

Yes I'm glad it was so simple and quick to fix my mic!

heyaly - 回复

Red wire to pin 3? Seems to go against the pin 2 hot method?

Jim - 回复

I'm not familiar with the "pin 2 hot method." We took a working mic apart and reassembled it the way we found it, so I'm pretty that is the correct soldering configuration.

Daniel Berger -

Świetna strona. Brawo.

Kazimierz Serafin - 回复

Add Comment

View Statistics:

Past 24 Hours: 11

Past 7 Days: 46

Past 30 Days: 175

All Time: 21,279