修复你的物品 社区 商店

Shark Ultimate Professional Circuit Board Replacement

简介

Before beginning this guide, ensure that the device is both unplugged and cool; failure to do so may result in electrocution or burns.

你所需要的

  1. Shark Ultimate Professional Circuit Board Replacement, Circuit Board: 步骤 1 中的图像 1，3 Shark Ultimate Professional Circuit Board Replacement, Circuit Board: 步骤 1 中的图像 2，3 Shark Ultimate Professional Circuit Board Replacement, Circuit Board: 步骤 1 中的图像 3，3

    • Use the Philips head #0 screwdriver to remove the two 11.49mm screws at the back of the iron.

    • Remove the back cover piece.

    • Make sure the iron is unplugged and cooled off.

    编辑

  2. Shark Ultimate Professional Circuit Board Replacement: 步骤 2 中的图像 1，2 Shark Ultimate Professional Circuit Board Replacement: 步骤 2 中的图像 2，2

    • Use the Philips head #0 screwdriver to remove the two 11.77mm screws holding the white clamp to the iron.

    • Use the Philips head #0 screwdriver to remove the two 6.58mm screws holding the black wires to the body of the iron.

    • Removing the left black wire will also free the red wire, attached by the same screw.

    编辑

  3. Shark Ultimate Professional Circuit Board Replacement: 步骤 3 中的图像 1，1

    • Pull the split end of the power cord upward through the ball joint.

    • Set aside the power cord.

    编辑

  5. Shark Ultimate Professional Circuit Board Replacement: 步骤 4 中的图像 1，3 Shark Ultimate Professional Circuit Board Replacement: 步骤 4 中的图像 2，3 Shark Ultimate Professional Circuit Board Replacement: 步骤 4 中的图像 3，3

    • Use the Philips head #0 screwdriver to remove the remaining 6.58mm screws that hold the wires on the bottom (brown and blue).

    • Remove from left to right

    • Unclip the black adapter piece on the bottom right.

    • Wires order (from left to right): Brown, Blue, Red, Black

    编辑

  6. Shark Ultimate Professional Circuit Board Replacement: 步骤 5 中的图像 1，2 Shark Ultimate Professional Circuit Board Replacement: 步骤 5 中的图像 2，2

    • Use the Philips head #0 screwdriver to remove the two 9.75mm screws (left and right) affixed to the circuit board.

    编辑

  7. Shark Ultimate Professional Circuit Board Replacement: 步骤 6 中的图像 1，2 Shark Ultimate Professional Circuit Board Replacement: 步骤 6 中的图像 2，2

    • Use the Philips head #0 screwdriver to remove the two 9.82mm screws (left and right) from the white border on top of the circuit board.

    • Gently pull the circuit board from affixed position.

    • The circuit board will not be completely separated at this point.

    编辑

  8. Shark Ultimate Professional Circuit Board Replacement: 步骤 7 中的图像 1，3 Shark Ultimate Professional Circuit Board Replacement: 步骤 7 中的图像 2，3 Shark Ultimate Professional Circuit Board Replacement: 步骤 7 中的图像 3，3

    • Remove the mode display piece and set aside.

    • Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle.

    编辑

  9. Shark Ultimate Professional Circuit Board Replacement: 步骤 8 中的图像 1，1

    • Remove the connecting wire from the connected adapter in the handle by pulling lightly.

    • Set aside the circuit board.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

5等其他人完成本指南。

作者

与5其他贡献者

Drew Carff

于10/23/17注册

868 声望

创作了5篇指南

徽章: 14

+ 11更多徽章

团队

USF Tampa, Team S1-G4, Leahy Fall 2017 USF Tampa, Team S1-G4, Leahy Fall 2017 的会员

USFT-LEAHY-F17S1G4

3 名成员

创作了10篇指南

4条评论

My shark 1505C does not have philips screws on the back. They are security torx and I cannot find a tool to open it.

Where can I buy a main board for this iron ?

Thanks

NevG.

nevstarg - 回复

where do I buy it's circuit board?

egovieira - 回复

Where can u buy the circuit board professional 1800 version?

Astinder Singhera - 回复

How much does the circuit board cost? and where can i purchase it?

D.A. Willis - 回复

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 2

过去 30 天： 26

总计 3,065