修复你的物品 社区 商店

Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement

简介

When the roller brush is not spinning because of a broken belt or damaged teeth, you might want to consider replacing the belt.

你所需要的

  1. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement, Roller Brush: 步骤 1 中的图像 1，2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement, Roller Brush: 步骤 1 中的图像 2，2

    • Push the red Lift Away button down and lift up on the vacuum handle to detach the base.

    • The handle was removed for convenience but is not required.

    编辑

  2. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 2 中的图像 1，1

    • Turn over the vacuum to reveal the roller brush.

    编辑

  3. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 3 中的图像 1，2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 3 中的图像 2，2

    • Pry the small wheels at the bottom of the base using the plastic opening tool.

    编辑

  4. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 4 中的图像 1，2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 4 中的图像 2，2

    • Using a coin, turn the big white knobs located above the roller brush counter-clockwise.

    编辑

  6. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 5 中的图像 1，3 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 5 中的图像 2，3 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 5 中的图像 3，3

    • Lift up the suction hose to reveal a screw.

    • Remove the 12.7 mm Phillips #02 screw.

    编辑

  7. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 6 中的图像 1，2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 6 中的图像 2，2

    • Remove eight 12.7mm screws located under the vacuum using a Phillips #02 screwdriver.

    • Remove two 12.7 mm screws located next to the wheels with a Phillips #02 screwdriver.

    • The two screws located next to the wheels are smaller in diameter.

    编辑

  8. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 7 中的图像 1，3 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 7 中的图像 2，3 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 7 中的图像 3，3

    • Turn the vacuum upright and pull the white upper section of the brush roller circuit housing.

    • Be careful when lifting the housing as there is a connector attached.

    编辑

  9. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 8 中的图像 1，2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 8 中的图像 2，2

    • Remove the connector attached to the circuit boards using a plastic opening tool.

    编辑

  10. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 9 中的图像 1，3 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 9 中的图像 2，3 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 9 中的图像 3，3

    • Remove the two 12.7 mm screws located at the top of the clear plastic brush roller housing using a Phillips #02 screwdriver.

    • Lift the clear plastic brush roller housing.

    编辑

  11. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 10 中的图像 1，2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 10 中的图像 2，2

    • Wiggle the brush roller upwards from the left and right side slots.

    编辑

  12. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement, Roller Brush Belt: 步骤 11 中的图像 1，1

    • Remove the roller brush by sliding it out toward the left, off the belt.

    编辑

  13. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Belt Replacement: 步骤 12 中的图像 1，1

    • Remove the belt from the motor gear by sliding the belt away from the gear and belt motor.

    • In the following picture the belt was already removed.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与4其他贡献者

Daniel Ceja

于01/24/19注册

277 声望

创作了2篇指南

徽章: 6

+ 3更多徽章

团队

Cal Poly, Team S19-G3, White Winter 2019 Cal Poly, Team S19-G3, White Winter 2019 的会员

CPSU-WHITE-W19S19G3

5 名成员

创作了12篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 2

过去 7 天： 6

过去 30 天： 13

总计 560