简介

A damaged hose will not allow the vacuum to function properly. This guide will assist in the replacement process. The hose is electrically attached to the other components of the vacuum. Removal of the hose will require electrical components.

  1. Press down on the hose release button  and pull away from the vacuum Press down on the hose release button  and pull away from the vacuum
    • Press down on the hose release button and pull away from the vacuum

  2. Press down on the wand release button and remove the  wand from the vacuum. Press down on the wand release button and remove the  wand from the vacuum. Press down on the wand release button and remove the  wand from the vacuum.
    • Press down on the wand release button and remove the wand from the vacuum.

  3. Press down on the handle release button and pull the  wand away from the vacuum. Press down on the handle release button and pull the  wand away from the vacuum. Press down on the handle release button and pull the  wand away from the vacuum.
    • Press down on the handle release button and pull the wand away from the vacuum.

  4. Remove  five 13.4 mm screws from the handle with a T20 Torx bit. Remove  five 13.4 mm screws from the handle with a T20 Torx bit.
    • Remove five 13.4 mm screws from the handle with a T20 Torx bit.

  5. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店
  6. Using a T20 Torx bit, remove the two 13.4 mm screws from the front of the nozzle.
    • Using a T20 Torx bit, remove the two 13.4 mm screws from the front of the nozzle.

  7. Remove the neck ring by placing a spudger under the brace  and lifting outwards. It may be helpful to use a heat gun on the brace and then attempt removing with a spudger. It may be helpful to use a heat gun on the brace and then attempt removing with a spudger.
    • Remove the neck ring by placing a spudger under the brace and lifting outwards.

    • It may be helpful to use a heat gun on the brace and then attempt removing with a spudger.

  8. Run the spudger along the center seam of the handle, pulling it apart as you go.
    • Run the spudger along the center seam of the handle, pulling it apart as you go.

  9. Remove the single 13.4 mm screw at the bottom of the handle grip and then lift the grip with a spudger. Remove the single 13.4 mm screw at the bottom of the handle grip and then lift the grip with a spudger.
    • Remove the single 13.4 mm screw at the bottom of the handle grip and then lift the grip with a spudger.

  10. Remove the single 13.4 mm screw from underneath the handle grip. You are then able to open the handle using a spudger and pulling the pieces apart. Remove the single 13.4 mm screw from underneath the handle grip. You are then able to open the handle using a spudger and pulling the pieces apart.
    • Remove the single 13.4 mm screw from underneath the handle grip. You are then able to open the handle using a spudger and pulling the pieces apart.

  11. Using two spudgers, unclip the hose from the handle. Using two spudgers, unclip the hose from the handle.
    • Using two spudgers, unclip the hose from the handle.

  12. Use wire cutters to clip the white and black wire that connect the hose to the handle. Soldering or wire connectors are necessary for reassembly.
    • Use wire cutters to clip the white and black wire that connect the hose to the handle.

    • Soldering or wire connectors are necessary for reassembly.

    • Any time you are dealing with electrical components, be sure the device is unplugged.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Sujey Ruano

于2018年10月08日注册

452 信誉积分

创作了3篇指南

团队

Cal Poly, Team S4-G6, White Fall 2018 Cal Poly, Team S4-G6, White Fall 2018 的会员

CPSU-WHITE-F18S4G6

4 名成员

创作了5篇指南

浏览统计数据:

过去的24小时: 2

过去的7天: 4

过去的30天: 15

总计 82