修复你的物品 社区 商店

Sceptre X9 Komodo VII Power Supply Unit Replacement

简介

Use this guide to remove the power supply unit.

你所需要的

  1. Sceptre X9 Komodo VII Power Supply Unit Replacement, Stand: 步骤 1 中的图像 1，1

    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

    编辑

  2. Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 2 中的图像 1，1

    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

    编辑

  3. Sceptre X9 Komodo VII Power Supply Unit Replacement, Board Cover: 步骤 3 中的图像 1，1

    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

    编辑

  5. Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 4 中的图像 1，3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 4 中的图像 2，3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 4 中的图像 3，3

    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

    编辑

  6. Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 5 中的图像 1，2 Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 5 中的图像 2，2

    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

    编辑

  7. Sceptre X9 Komodo VII Power Supply Unit Replacement, Power Supply Unit: 步骤 6 中的图像 1，1

    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

    编辑

  8. Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 7 中的图像 1，3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 7 中的图像 2，3 Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 7 中的图像 3，3

    • Unplug the seven connections from the power supply unit by gently pulling on them.

    编辑

  9. Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 8 中的图像 1，1

    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

    编辑

  10. Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 9 中的图像 1，2 Sceptre X9 Komodo VII Power Supply Unit Replacement: 步骤 9 中的图像 2，2

    • Lift the power supply unit straight up to remove it from the back panel.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与5其他贡献者

Jose Carrillo

于09/26/12注册

23 声望

撰写一个指南

徽章: 6

+ 3更多徽章

团队

Cal Poly, Team 16-56, Forte Fall 2012 Cal Poly, Team 16-56, Forte Fall 2012 的会员

CPSU-FORTE-F12S16G56

5 名成员

创作了13篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 1

总计 664