跳转到主内容

本指南有最近更改,您可查看未经巡查的最新版本

Sanyo VPC S1275 LCD Screen Replacement

你所需要的

  1. Sanyo VPC S1275 LCD Screen Replacement, Battery: 步骤 1 中的图像 1,1
    • Place your thumb on the right side of the camera over the battery door.

    • Slide the battery door to the right until the door lifts up.

  2. Sanyo VPC S1275 LCD Screen Replacement: 步骤 2 中的图像 1,1
    • Remove and recycle old batteries.

  3. Sanyo VPC S1275 LCD Screen Replacement, Case: 步骤 3 中的图像 1,3 Sanyo VPC S1275 LCD Screen Replacement, Case: 步骤 3 中的图像 2,3 Sanyo VPC S1275 LCD Screen Replacement, Case: 步骤 3 中的图像 3,3
    • Remove the following six screws using the Phillips #00 screwdriver:

    • Two screws on the left side of the camera.

    • Two screws on the right side of the camera.

    • Two screws on the bottom of the camera.

  4. Sanyo VPC S1275 LCD Screen Replacement: 步骤 4 中的图像 1,2 Sanyo VPC S1275 LCD Screen Replacement: 步骤 4 中的图像 2,2
    • Open the battery slot on the bottom of the camera by sliding the door to the right.

    • Remove the single 4 mm screw on the bottom right using the Phillips #00 screwdriver.

  5. Sanyo VPC S1275 LCD Screen Replacement: 步骤 5 中的图像 1,3 Sanyo VPC S1275 LCD Screen Replacement: 步骤 5 中的图像 2,3 Sanyo VPC S1275 LCD Screen Replacement: 步骤 5 中的图像 3,3
    • Insert a spudger in the seam at the bottom of the camera.

    • Gently separate the rear case from the front of the camera.

  6. Sanyo VPC S1275 LCD Screen Replacement: 步骤 6 中的图像 1,1
    • This step is only needed for the case and logic board replacement

    • Using the Phillips #00 screwdriver, remove the single screw attached to the front casing in the top left corner. The front case should easily separate.

  7. Sanyo VPC S1275 LCD Screen Replacement: 步骤 7 中的图像 1,1
    • This step is only needed for the case replacement.

    • Using the Phillips #00 screwdriver, remove the screw on the inside of the battery door.

    • Slide the battery door off of the hinge.

  8. Sanyo VPC S1275 LCD Screen Replacement, LCD Screen: 步骤 8 中的图像 1,2 Sanyo VPC S1275 LCD Screen Replacement, LCD Screen: 步骤 8 中的图像 2,2
    • Using the spudger, carefully lift up the LCD screen, making sure to keep the ribbon cable intact.

    • Place the LCD screen on a non-abrasive surface.

  9. Sanyo VPC S1275 LCD Screen Replacement: 步骤 9 中的图像 1,1
    • Using the spudger lift the black flap up to release the ribbon cable.

    • The LCD screen will now be completely detached from the camera.

结论

To reassemble your device, follow these instructions in reverse order.

Evan Perez

于04/15/10注册

19 声望

创作了2篇指南

团队

Cal Poly, Team 24-24, Regan Spring 2010 Cal Poly, Team 24-24, Regan Spring 2010 的会员

CPSU-REGAN-S10S24G24

4 名成员

创作了12篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 9

总计 3,068