跳转到主内容

简介

This guide can be used for those that are experiencing difficulties with their hold switch. A major sign of a faulty hold switch is being incapable of turning on the device. Use this guide to replace a faulty hold switch.

  1. Remove the battery compartment cover.
    • Remove the battery compartment cover.

    • Remove the battery.

  2. Locate and remove the screw next to the battery compartment lid.
    • Locate and remove the screw next to the battery compartment lid.

  3. Locate the interlocking pegs along the seam of the device's casings.
    • Locate the interlocking pegs along the seam of the device's casings.

    • Gently pry the pegs apart one at a time, working your way around the case.

    • Be careful when prying apart the pegs: they are made of plastic and may break.

  4. The battery contact springs may prevent the case from separating.
    • The battery contact springs may prevent the case from separating.

    • Push the battery contact springs down through the hole in the case.

  5. The casing protecting the USB and headphone jacks must be removed.
    • The casing protecting the USB and headphone jacks must be removed.

    • Locate and gently pry apart the two interlocking clips holding it in place.

    • The outer casings may now be removed and the MP3 player should separate.

  6. You now have access to all components found on the inside of the device!
    • You now have access to all components found on the inside of the device!

  7. Locate hold switch on motherboard.
    • Locate hold switch on motherboard.

  8. Locate where hold switch is connected to motherboard via soldered connections.
    • Locate where hold switch is connected to motherboard via soldered connections.

  9. Use the soldering iron to liquefy the solder connecting the hold switch to the motherboard.
    • Use the soldering iron to liquefy the solder connecting the hold switch to the motherboard.

  10. The solder and soldering iron will be very hot at this time. Do not touch unless wearing protective gloves as you will be burnt.
    • The solder and soldering iron will be very hot at this time. Do not touch unless wearing protective gloves as you will be burnt.

    • Be sure to always elevate the hot end of the soldering iron on a metal stand to prevent incidental burns.

  11. With the soldered points liquefied, remove faulty hold switch from the motherboard.
    • With the soldered points liquefied, remove faulty hold switch from the motherboard.

    • To do this liquefy the solder on each contact and remove them individually.

  12. Replace faulty hold switch with a new one.
    • Replace faulty hold switch with a new one.

  13. There may be some solder in the way of the hold switch's metal contacts. If this occurs simply melt/remove the solder to create room for the contacts.
    • There may be some solder in the way of the hold switch's metal contacts. If this occurs simply melt/remove the solder to create room for the contacts.

  14. With the new hold switch in place, use the soldering iron and solder to create a stable connection between the motherboard and hold switch.
    • With the new hold switch in place, use the soldering iron and solder to create a stable connection between the motherboard and hold switch.

    • Be sure to allow the new solder to cool and harden.

结论

To reassemble your device, follow these instructions in reverse order.

James Thorne

于2013年11月05日注册

625 信誉积分

创作了6篇指南

团队

UMass Dartmouth, Team 1-8, Shastany Fall 2013 UMass Dartmouth, Team 1-8, Shastany Fall 2013 的会员

UMASSD-SHASTANY-F13S1G8

3 名成员

创作了6篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 1

总计 420