简介

This guide is a step-by-step guide on how to replace a Samsung Juke logic board.

Locate the button on the bottom of the phone. Once located, press and hold the button down.
  • Locate the button on the bottom of the phone. Once located, press and hold the button down.

添加评论

While holding the button down, remove the back cover of the phone. While holding the button down, remove the back cover of the phone.
  • While holding the button down, remove the back cover of the phone.

添加评论

Use the size 00 Phillips screwdriver to remove the four screws located on the back of the phone. These screws are circled in yellow in the given image.
  • Use the size 00 Phillips screwdriver to remove the four screws located on the back of the phone. These screws are circled in yellow in the given image.

添加评论

Using the same 00 Phillips screwdriver, remove the two screws at the bottom back plate of the phone near the camera and the speaker.
  • Using the same 00 Phillips screwdriver, remove the two screws at the bottom back plate of the phone near the camera and the speaker.

  • These screws will be 7.25 mm long.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Before proceeding, locate the USB port (where the charger can be plugged in) and open it using the iFixit Opening Tool. Failure to open USB port cover at this stage may result in damaging the device. Failure to open USB port cover at this stage may result in damaging the device.
  • Before proceeding, locate the USB port (where the charger can be plugged in) and open it using the iFixit Opening Tool.

  • Failure to open USB port cover at this stage may result in damaging the device.

添加评论

Remove the screws on either side of the camera/speaker with a Phillips 00 screwdriver.
  • Remove the screws on either side of the camera/speaker with a Phillips 00 screwdriver.

  • These screws will be 5.45 mm long.

添加评论

Use the iFixit Opening Tool to begin removing the camera/speaker from the logic board. Practice caution to prevent damage to the attaching ribbon.
  • Use the iFixit Opening Tool to begin removing the camera/speaker from the logic board.

  • Practice caution to prevent damage to the attaching ribbon.

添加评论

To completely remove the camera/speaker, locate the orange attachment beneath it (as shown in the image). Then, use the iFixit Opening Tool to gently pry the camera/speaker off.
  • To completely remove the camera/speaker, locate the orange attachment beneath it (as shown in the image).

  • Then, use the iFixit Opening Tool to gently pry the camera/speaker off.

添加评论

Use the iFixit Opening Tool to pop off the yellow tab on the logic board. Use the iFixit Opening Tool to pop off the yellow tab on the logic board.
  • Use the iFixit Opening Tool to pop off the yellow tab on the logic board.

添加评论

Use the iFixit Opening Tool to pop off the other orange tab to free the logic board. Use the iFixit Opening Tool to pop off the other orange tab to free the logic board.
  • Use the iFixit Opening Tool to pop off the other orange tab to free the logic board.

添加评论

To completely remove the logic board, use the iFixit Opening Tool to pop it up, then use your fingers to pull it out. Do not be alarmed if the volume and hold switch buttons are removed from the logic board. Do not be alarmed if the volume and hold switch buttons are removed from the logic board.
  • To completely remove the logic board, use the iFixit Opening Tool to pop it up, then use your fingers to pull it out.

  • Do not be alarmed if the volume and hold switch buttons are removed from the logic board.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

Renee Kuzniar

于2010年04月13日注册

82 信誉积分

创作了8篇指南

团队

Cal Poly, Team 6-18, Maness Spring 2010 Cal Poly, Team 6-18, Maness Spring 2010 的会员

CPSU-MANESS-S10S6G18

3 名成员

创作了12篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 1

总计 2,675