简介

Use this guide to replace the front panel display assembly in your Samsung Galaxy Note.

  1. Grasp the cap of the stylus and remove it from its slot in the midframe.
    • Grasp the cap of the stylus and remove it from its slot in the midframe.

    添加评论

  2. Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.
    • Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.

    添加评论

    • Lift and remove the rear case from the phone.

    添加评论

    • Insert your finger in the notch of the battery compartment.

    • Press the battery toward the rear facing camera while pulling outward.

    添加评论

    • Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

    • After the click, release the card and it will pop out of its slot.

    • For reassembly, push the microSD card into the slot until it clicks in place.

    添加评论

    • Remove the microSD card from its slot in the midframe.

    添加评论

    • Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment.

    添加评论

    • Slide the SIM card out the rest of the way with your thumb and remove it from the device.

    添加评论

    • Remove the nine 3.4 mm Phillips #00 screws securing the midframe to the display assembly.

    添加评论

    • Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry.

    添加评论

    • Slide the plastic opening tool down the seam.

    添加评论

  3. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Insert your plastic opening tool to the left of the headphone jack between the midframe and the display assembly.

    • Slide the opening tool along the top edge of the phone.

    • Continue to run the plastic opening tool around the perimeter of the phone until the midframe is separated.

    添加评论

    • Remove the midframe from the display assembly.

    添加评论

    • Use the flat end of a spudger to carefully disconnect the display cable connector.

    添加评论

    • Use a spudger to disconnect the front-facing camera assembly cable connector.

    • Disconnect the headphone jack/earpiece speaker assembly cable connector.

    • Disconnect the digitizer cable connector.

    添加评论

    • Disconnect the soft button cable connector with the flat end of a spudger.

    • Use a spudger to disconnect the USB board cable connector.

    • Disconnect the antenna cable connector.

    添加评论

    • Remove the two 3.4 mm Phillips #00 screws securing the motherboard to the display assembly.

    添加评论

    • Remove the motherboard assembly from the display assembly.

    添加评论

    • Remove the two 3 mm Phillips #00 screws securing the upper display assembly bracket.

    添加评论

    • Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket.

    添加评论

    • Using tweezers, or your fingers, remove the front-facing camera assembly.

    添加评论

    • Use the tip of a spudger to pry the headphone jack/earpiece speaker assembly out of its recess in the display assembly.

    添加评论

    • Use tweezers, or your fingers, to remove the headphone jack/earpiece speaker assembly.

    添加评论

    • Remove the three 3 mm Phillips #00 screws securing the speaker enclosure to the front panel assembly.

    添加评论

    • Lift the speaker enclosure from the display assembly.

    添加评论

    • Use the tip of a spudger to disconnect the antenna cable connector from the USB board.

    • Remove the antenna cable.

    添加评论

    • Push the flat end of a spudger under the USB board to separate it from the display assembly.

    • Insert the spudger at a shallow angle to avoid bending or damaging the USB board.

    添加评论

    • Remove the USB board.

    添加评论

    • Insert the tip of a spudger under the vibrator connector cable near the contacts then slide toward the vibrator itself.

    添加评论

    • Insert the flat end of a spudger under the vibrator connector cable, and pry it up from the adhesive.

    添加评论

    • Remove the vibrator from the display assembly.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

36等其他人完成本指南。

Sam Lionheart

于2012年10月18日注册

345,694 信誉积分

创作了535篇指南

团队

iFixit iFixit 的会员

Community

113 名成员

创作了7,342篇指南

étape 31 ensuite ??

Fabrice - 回复

i have a galaxy not and its display is badly broken,at the top of the phone(front side),the display is broken so badly that i am able to a little circuit i.e. a brown color wire which is connected to the display.

so my ques. is that can the phone work after repairing or it has gone?

Abhishek Kumbhar - 回复

Hello Abhishek Kumbhar, if the motherboard is not damaged it's all fine. All other parts are replaceable

Georg Fischer - 回复

excellent photos

of samsung 717

murali maroju - 回复

i am trying to get my phone to charge but its not and i have it pluged in and it doesnt want to charge

Anthany Kleven - 回复

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 21

过去的30天: 83

总计 41,964