修复你的物品 社区 商店

Samsung CLP-300 Black Toner Transfer Unit Replacement

简介

Follow these steps if you are experiencing uneven print quality or lines in your printed documents.

你所需要的

  1. Samsung CLP-300 Black Toner Transfer Unit Replacement, Black Toner Transfer Unit: 步骤 1 中的图像 1，1

    • Turn the printer off and wait a few minutes for it to cool.

    编辑

  2. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 2 中的图像 1，1

    • Pull paper tray out and set aside.

    编辑

  3. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 3 中的图像 1，2 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 3 中的图像 2，2

    • Open the front cover.

    编辑

  4. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 4 中的图像 1，1

    • Pull the waste toner container out of the printer using the handle.

    • Make sure to keep waste toner container upright to avoid spillage.

    编辑

  6. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 5 中的图像 1，3 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 5 中的图像 2，3 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 5 中的图像 3，3

    • Pull the imaging unit out of the printer using bottom handle.

    • Use green handle on top of imaging unit to steady unit as you pull it out.

    • At this point you can set the printer aside as you will only need the imaging unit to continue repair.

    编辑

  7. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 6 中的图像 1，2 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 6 中的图像 2，2

    • Remove these two screws.

    • Do not expose imaging unit to light for more than a few minutes. Covering unit with a piece of paper is sufficient protection while you complete repair.

    编辑

  8. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 7 中的图像 1，1

    • Carefully pry plastic arm away from main unit.

    编辑

  9. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 8 中的图像 1，3 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 8 中的图像 2，3 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 8 中的图像 3，3

    • Carefully pry plastic from screw base so that the entire organic photo conductor piece slides open to the left.

    • When removing the organic photo conductor take care to not lose the small spring on the back left.

    • At this point you may want to put on plastic gloves to keep from staining hands with printer ink.

    编辑

  10. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 9 中的图像 1，2 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 9 中的图像 2，2

    • Slide each toner transfer unit out separately, placing all aside except for the black toner transfer unit.

    • Keep toner rollers level to avoid toner spillage.

    编辑

  11. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 10 中的图像 1，3 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 10 中的图像 2，3 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 10 中的图像 3，3

    • Remove these five screws from the top of the black toner transfer unit.

    • Remove main and smaller z-shaped plates.

    编辑

  12. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 11 中的图像 1，2 Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 11 中的图像 2，2

    • Remove these three screws from the right end of the toner transfer unit.

    编辑

  13. Samsung CLP-300 Black Toner Transfer Unit Replacement: 步骤 12 中的图像 1，1

    • Remove plastic end piece.

    • Gently pull out black toner roller.

    • Insert new roller in place of old roller turning slightly to fit.

    • Be careful not to pinch small foam square when inserting new roller.

    • Cover new roller with toner by rotating roller by hand.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

作者

与5其他贡献者

Heather Howard

于10/15/14注册

586 声望

创作了4篇指南

徽章: 8

+ 5更多徽章

团队

University of Maine, Team 1-1, Diaz Fall 2014 University of Maine, Team 1-1, Diaz Fall 2014 的会员

UMAINE-DIAZ-F14S1G1

3 名成员

创作了8篇指南

2条评论

I need more information pertaining step 8. In order to separate the parts, in which directions should the be moved first and where is the best point to apply force ?

Bernd Dreyer - 回复

I need more information for step 12: I removed the old roller. Unfortunately I don't know anymore how exactly the metal discs and the white plastic rings are placed.

Daniel Roller - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 5

过去 30 天： 15

总计 3,288