跳转到主内容

SG 552-1 Commando Safety Replacement

你所需要的

  1. SG 552-1 Commando Safety Replacement, Gearbox: 步骤 1 中的图像 1,2 SG 552-1 Commando Safety Replacement, Gearbox: 步骤 1 中的图像 2,2
    • Using a flathead screwdriver, remove the pin holding the hand guard in place.

    • To remove this, turn the pin clockwise and push it through at the same time.

    • Remove the hand guard.

  2. SG 552-1 Commando Safety Replacement: 步骤 2 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 2 中的图像 2,2
    • Using a Phillips #1 screwdriver, remove the two 8mm screws above the hand guard on both sides of the gun.

    • There should be four total.

  3. SG 552-1 Commando Safety Replacement: 步骤 3 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 3 中的图像 2,2
    • Turn the gun over so that you are facing the bottom of the gun.

    • Using a Phillips #1 screwdriver, remove the following screws:

    • Remove the 8mm screw that is located directly underneath the cocking lever.

    • Remove the 8mm screw located beside the screw you just removed.

  4. SG 552-1 Commando Safety Replacement: 步骤 4 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 4 中的图像 2,2
    • Carefully tug on the tip of the gun and pull the barrel and its cover out.

  5. SG 552-1 Commando Safety Replacement: 步骤 5 中的图像 1,3 SG 552-1 Commando Safety Replacement: 步骤 5 中的图像 2,3 SG 552-1 Commando Safety Replacement: 步骤 5 中的图像 3,3
    • Locate the hand grip.

    • Using a Phillips #0 screwdriver, remove the two 6mm screws at the bottom of the hand grip.

    • Slide the cover off.

  6. SG 552-1 Commando Safety Replacement: 步骤 6 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 6 中的图像 2,2
    • Pull the motor out of the hand grip.

    • Using a Phillips #1 screwdriver, remove the two 5mm screws inside of the hand grip.

  7. SG 552-1 Commando Safety Replacement: 步骤 7 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 7 中的图像 2,2
    • Locate the pin holding the folding stock in place.

    • Using an allen wrench or something small, carefully push the pin out.

  8. SG 552-1 Commando Safety Replacement: 步骤 8 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 8 中的图像 2,2
    • Using a Phillips #1 screwdriver, remove the 20mm screw behind the folding stock and above the gearbox.

    • Remove the cover that was held on by the screw.

  9. SG 552-1 Commando Safety Replacement: 步骤 9 中的图像 1,3 SG 552-1 Commando Safety Replacement: 步骤 9 中的图像 2,3 SG 552-1 Commando Safety Replacement: 步骤 9 中的图像 3,3
    • Using a flathead screwdriver, remove the two 5mm screws beside the safety switch on both sides of the gun.

    • Slide off the piece that was held on by those screws.

  10. SG 552-1 Commando Safety Replacement: 步骤 10 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 10 中的图像 2,2
    • Using a small allen wrench, carefully unscrew the screws holding the safety switch in place on both sides of the gun.

    • The screws do not have to be taken out all the way, just slightly loosen them until you are able to pull the switch off.

  11. SG 552-1 Commando Safety Replacement: 步骤 11 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 11 中的图像 2,2
    • Using a Phillips #0 screwdriver, remove the two 6mm screws that were underneath the safety switch on both sides of the gun.

    • Carefully remove the pieces that were held on by the screws.

  12. SG 552-1 Commando Safety Replacement: 步骤 12 中的图像 1,3 SG 552-1 Commando Safety Replacement: 步骤 12 中的图像 2,3 SG 552-1 Commando Safety Replacement: 步骤 12 中的图像 3,3
    • Pull apart the cover when pulling the gearbox out.

    • Pull the gearbox out.

    • The gears will fall out when taking the gearbox out. Careful not to lose them.

  13. SG 552-1 Commando Safety Replacement, Safety: 步骤 13 中的图像 1,1
    • Using a Phillips #0 screwdriver, remove the single 3mm screw holding the safety/trigger cover in place.

  14. SG 552-1 Commando Safety Replacement: 步骤 14 中的图像 1,2 SG 552-1 Commando Safety Replacement: 步骤 14 中的图像 2,2
    • Remove the cover over the trigger.

    • The safety is located underneath the cover.

结论

To reassemble your device, follow these instructions in reverse order.

Anika Morris

于10/05/12注册

1 声望

创作了4篇指南

团队

Cal Poly, Team 18-41, Regan Fall 2012 Cal Poly, Team 18-41, Regan Fall 2012 的会员

CPSU-REGAN-F12S18G41

6 名成员

创作了6篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 4

总计 703