修复你的物品 社区 商店

Ryobi RJ1861V Motor Housing Replacement

你所需要的

  1. Ryobi RJ1861V Motor Housing Replacement, Saw Bar Assembly: 步骤 1 中的图像 1，1

    • Use a Torx T5 screwdriver to remove the single 8 mm screw securing the shoe.

    翻译

  2. Ryobi RJ1861V Motor Housing Replacement: 步骤 2 中的图像 1，2 Ryobi RJ1861V Motor Housing Replacement: 步骤 2 中的图像 2，2

    • Remove the rubber sleeve.

    • You may have to use some force as it has a tight fit.

    翻译

  3. Ryobi RJ1861V Motor Housing Replacement: 步骤 3 中的图像 1，1

    • Use a Torx T5 screwdriver to remove the six screws on the underside of the device.

    翻译

  4. Ryobi RJ1861V Motor Housing Replacement: 步骤 4 中的图像 1，1

    • Use a Torx T5 screwdriver to remove the four screws on the top of the gear case.

    • There are two screws on each side of the device.

    翻译

  5. Ryobi RJ1861V Motor Housing Replacement: 步骤 5 中的图像 1，1

    • Remove the backside panel.

    翻译

  7. Ryobi RJ1861V Motor Housing Replacement: 步骤 6 中的图像 1，1

    • Unscrew the four T5 Torx screws that hold the assembly bar in place.

    翻译

  8. Ryobi RJ1861V Motor Housing Replacement: 步骤 7 中的图像 1，1

    • Lift the assembly bar up and out of the chassis.

    翻译

  9. Ryobi RJ1861V Motor Housing Replacement, Assembly Bar Bearing: 步骤 8 中的图像 1，1

    • Begin with the top of the device facing up.

    翻译

  10. Ryobi RJ1861V Motor Housing Replacement: 步骤 9 中的图像 1，1

    • Insert needle nose pliers to remove the retaining pin at the top of the bearing.

    翻译

  11. Ryobi RJ1861V Motor Housing Replacement: 步骤 10 中的图像 1，1

    • Once the retaining pin has been removed, pull off the damaged bearing and insert a new one.

    翻译

  12. Ryobi RJ1861V Motor Housing Replacement, Motor Housing: 步骤 11 中的图像 1，2 Ryobi RJ1861V Motor Housing Replacement, Motor Housing: 步骤 11 中的图像 2，2

    • After following prerequisite guides to get to the presented step, remove motor assembly from back housing.

    • Motor Assembly will be greasy

    • Motor Assembly

    • Motor Assembly Housing

    翻译

  13. Ryobi RJ1861V Motor Housing Replacement: 步骤 12 中的图像 1，1

    • Using pliers to grab onto the elongated aluminium exterior of the housing, begin to slowly wiggle the motor assembly housing until it comes loose.

    翻译

  14. Ryobi RJ1861V Motor Housing Replacement: 步骤 13 中的图像 1，1

    • Detach red wires from base of the back of the housing .

    翻译

  15. Ryobi RJ1861V Motor Housing Replacement: 步骤 14 中的图像 1，1

    • After the wires have been detached it should be relatively easy to remove and replace the Motor Assembly Housing

    • Motor Assembly Housing

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 2

过去 30 天： 2

总计 67