简介

Stalled printer for error 0xF2 or 0xF3

The error compare when there are some problem with encoder with roller to feed paper.

  1. Remove the external component
    • Remove the external component

    • Remove all component

    • Remove Ink tanks

    添加评论

  2. remove windows
    • remove windows

    添加评论

    • Remove Rear component

    添加评论

    • Dismount Ink lever

    添加评论

    • Remove Front pannel screws

    添加评论

  3. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Dismount LCD Pannel

    添加评论

    • Remove front pannel

    添加评论

    • Remove back panel screws

    添加评论

    • Other back panel screw (you find i back the lcd display)

    添加评论

    • Remove back ethernet panel

    添加评论

    • Remove main back panel, make attention to lcd display

    添加评论

    • More gently clean left encoder with a dry cleenex

    添加评论

    • More gently, Clean right encoder with a dry cleenex

    添加评论

    • If you want test the printer you need insert paper, and cover 2 switch with paper scotch.

    添加评论

    • Remount the printer (but before remove the scotch if you have used it) following in reverse mode the previous instructions.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

14等其他人完成本指南。

delete

于2012年11月15日注册

482 信誉积分

撰写一个指南

It's works, thanks

Thom - 回复

Perfect. I used this guide to disassemble my printer.

I had 0xF1 and/or 0xF4. The reason was some paper stuck between the gears of the paper feed (in this guide step 12).

I hope this hint will help others. I didn't find any info about these error code online.

DumahBrazorf - 回复

Error descriptions I found here - http://www.fatalerrors.info/

John Smith -

Thank you very much ! This is a very useful and beautifully documented guide. Best wishes and greetings to the kind author of this guide from Bratislava, Slovakia.

George Pekarovic

George - 回复

muito obrigado pela ajuda

Filipe Rocha - 回复

You are awesome! It helped me! Thanks very much!

martinjurtik - 回复

Hi

I keep getting on an Epson B-500DN printer error restart printer with the paper and ink led blinking orange.

Disassemble the printer made a full cleaning (all encoding wheels too) and keep getting this error, the printer goes until ready, then as soon as it says printing it shows the error.

anyone ???

invitro59 - 回复

OMG.

I had error oxF3.

I was set to bin this ace printer, I just googled the error code and bam this guide came up. This was awesome, I only found a little dirt on the step 12 clear plastic disc, nothing visible on step 13. Put the cartridges back in, maintenance tank paper tray and hooked up the power and network cable, and covered the 2 switches with tape. then OMG it worked. Now need to work out which screw goes where and reassemble.

Malcolm Taylor - 回复

OK. Seguito con semplicità e Risolto il Problema. Adesso funziona. OK Thank you

Foto Diego - 回复

What about Erro code 0xF3 in Epson WF7610

ABEL MLIGA - 回复

Yes what about the WF7610 error code 0xF3?!

David Imondi - 回复

I have Epson XP 710 which shows an error code 0×4f what can i do for it. When i turned it on it's starts well with Epson logo but there's a sound of running the gears in fast speed for a few seconds after this it's showing the error just after pooping up the menu screen no head movement. Kindly forward me with possible assistance

abab6330 - 回复

Constantly gives 0xF4. If you move the head to the center, when it is turned on, it goes to the left, then goes to its place and when Parking the engine PF PID (left) twitches a little, and the scoreboard error 0xF4. In printer all cleaned up, blew. Cartridges took out, got a diaper. Before that, it was so that it prints, then outputs 0xF4 and sometimes 0xF1. What to do?

561054 - 回复

添加评论

浏览统计数据:

过去的24小时: 44

过去的7天: 234

过去的30天: 965

总计 46,751