配件

无需配件。

  1. Tool on left - PH000 screwdriver
    • Tool on left - PH000 screwdriver

    • Tool on right - iPod fix-it tool

    • Soldering Iron

  2. Locate the 3 black screws on the bottom of the camera and the 2 gray screws on each side of the camera. Remove them with a PH000 screwdriver.
    • Locate the 3 black screws on the bottom of the camera and the 2 gray screws on each side of the camera. Remove them with a PH000 screwdriver.

  3. Locate the gray band that you removed the screws from; this holds the two halves of the camera together.  Use an iPod fix-it tool to pry the gray band loose and remove it. Locate the gray band that you removed the screws from; this holds the two halves of the camera together.  Use an iPod fix-it tool to pry the gray band loose and remove it.
    • Locate the gray band that you removed the screws from; this holds the two halves of the camera together. Use an iPod fix-it tool to pry the gray band loose and remove it.

  4. Use the iPod fix-it tool to separate the back panel from the camera.
    • Use the iPod fix-it tool to separate the back panel from the camera.

  5. Use the iPod fix-it tool to carefully pry the screen from the logic board.
    • Use the iPod fix-it tool to carefully pry the screen from the logic board.

    • There's a ribbon cable that connects the screen to the logic board.

  6. 所有超过US$100或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店
  7. This view shows the ribbon cable that connects to the screen.
    • This view shows the ribbon cable that connects to the screen.

  8. Flip the screen down.  To disconnect the ribbon cable from the logic board, rock each end of the brown metal retainer that holds the ribbon cable in place until the ribbon disconnects.
    • Flip the screen down. To disconnect the ribbon cable from the logic board, rock each end of the brown metal retainer that holds the ribbon cable in place until the ribbon disconnects.

  9. Remove the two screws on the top edge of the circuit board to the right of the viewfinder.
    • Remove the two screws on the top edge of the circuit board to the right of the viewfinder.

  10. To connect the new screen, solder the wires in place and connect the ribbon cable to the logic board.
    • To connect the new screen, solder the wires in place and connect the ribbon cable to the logic board.

  11. Unthread the four wires running across the top of the viewfinder from the plastic brackets holding them in place.
    • Unthread the four wires running across the top of the viewfinder from the plastic brackets holding them in place.

  12. Remove the two black screws threaded vertically into the top of the viewfinder. Loosen the flash and circuit board for more accessibility.  This will allow for the viewfinder to be replaced.
    • Remove the two black screws threaded vertically into the top of the viewfinder. Loosen the flash and circuit board for more accessibility. This will allow for the viewfinder to be replaced.

  13. Remove the small piece of tape holding the four wires to the viewer. Remove the small piece of tape holding the four wires to the viewer.
    • Remove the small piece of tape holding the four wires to the viewer.

  14. Remove the two screws on the top edge of the circuit board, to the right of the viewer. Remove the two screws on the top edge of the circuit board, to the right of the viewer.
    • Remove the two screws on the top edge of the circuit board, to the right of the viewer.

结论

To reassemble your device, follow these instructions in reverse order.

Andrew

于2012年09月27日注册

7 信誉积分

撰写一个指南

团队

Ohio State, Team 1-2, Buehl Fall 2012 Ohio State, Team 1-2, Buehl Fall 2012 的会员

OSU-BUEHL-F12S1G2

3 名成员

创作了3篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 2

总计 770