简介

This guide will show you how to remove the power supply on your HP Compaq dx2000MT.

  1. Turn off your computer and remove the power cable by pulling it straight out of its socket.
    • Turn off your computer and remove the power cable by pulling it straight out of its socket.

  2. Remove the 2 Phillips #2 screws that secure the case door to the device. Remove the 2 Phillips #2 screws that secure the case door to the device.
    • Remove the 2 Phillips #2 screws that secure the case door to the device.

  3. Remove the side case door by pushing towards the rear of the device with your hand. This may take considerable force so keep pushing! Once you slide the door back, remove it by pulling it outwards from the device.
    • Remove the side case door by pushing towards the rear of the device with your hand.

      • This may take considerable force so keep pushing!

    • Once you slide the door back, remove it by pulling it outwards from the device.

  4. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  5. Remove the side case door by pushing towards the rear of the device with your hand. Once again, this may take considerable force. Once you slide the door back, remove it by pulling it outwards from the device.
    • Remove the side case door by pushing towards the rear of the device with your hand.

      • Once again, this may take considerable force.

    • Once you slide the door back, remove it by pulling it outwards from the device.

  6. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.
    • Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

  7. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.
    • Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

  8. Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply
    • Remove the 4 Torx T15 screws from the rear of the power supply

  9. Slide the power supply towards the front of the device Keep your hand underneath it! You don't want to drop it!
    • Slide the power supply towards the front of the device

    • Keep your hand underneath it! You don't want to drop it!

    • Then pull the power supply down and remove it from the case.

结论

To reassemble your device, follow these instructions in reverse order.

7等其他人完成本指南。

Logan Pace

于2011年10月12日注册

2,020 信誉积分

创作了9篇指南

团队

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011 的会员

CPSU-REGAN-F11S17G16

4 名成员

创作了17篇指南

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 9

总计 2,448