Razer Basilisk V3 Scroll Wheel Assembly Replacement

简介

It is not uncommon for mice, such as the Razer Basilisk V3, to see mechanical difficulties through wear and tear of the mouse. In order to fix issues such as unregistered scrolls, double scrolling, or general friction, it might be necessary to take apart the mouse and perform a replacement. Additionally, customization and upgrades could also be a reason to replace the scroll wheel.

It should be noted that disassembling the mouse to replace the scroll wheel will most likely damage the mouse skates. Also, it is helpful for users to have knowledge in basic electronics as well as the internal structure of a mouse. This guide will assist in replacing the Basilisk V3 scroll wheel.

你所需要的

步骤 1 Skates

Razer Basilisk V3 Scroll Wheel Assembly Replacement, Skates: 步骤 1 中的图像 1，1

Locate the highlighted white skates on the bottom of the mouse.

编辑

步骤 2

Razer Basilisk V3 Scroll Wheel Assembly Replacement: 步骤 2 中的图像 3，3

Heat the skate using a heat gun or hair dryer.
Using the pointy end of the spudger pry away a corner of the skate.
If the adhesive does not pull away easily, heat the skate more.
Once the corner of the skate comes free use the flat end of the spudger to peel off the rest of the skate.
Repeat these steps for each of the skates.

编辑

步骤 3 Backplate

Razer Basilisk V3 Scroll Wheel Assembly Replacement, Backplate: 步骤 3 中的图像 1，1

Remove two 4.8 mm screws that were hidden under the front skates using a JIS #1 screwdriver.
Remove the single 4 mm screw beneath the thumb grip using a JIS #1 screwdriver.

编辑

步骤 4

Razer Basilisk V3 Scroll Wheel Assembly Replacement: 步骤 4 中的图像 3，3

Heat the label gently with a heat gun or hair dryer.
Once the adhesive is loosened, use a spudger to peel off the label carefully, revealing two additional screws.
Remove the two 4.8 mm screws using a JIS #1 screwdriver.

编辑

步骤 5

Razer Basilisk V3 Scroll Wheel Assembly Replacement: 步骤 5 中的图像 3，3

Carefully pry apart the mouse's top and bottom halves. Using the iFixit opening tool, start at one corner and work around the edge.
Be cautious of the clips that may break during this process.
Using a plastic opening tool, gently pry the connector apart by moving side to side to avoid bending the pins.
When reassembling, be mindful that the connector only fits one way, as shown in the pictures.

编辑

步骤 6 Scroll Wheel Assembly

Razer Basilisk V3 Scroll Wheel Assembly Replacement, Scroll Wheel Assembly: 步骤 6 中的图像 1，3

Razer Basilisk V3 Scroll Wheel Assembly Replacement, Scroll Wheel Assembly: 步骤 6 中的图像 2，3

Razer Basilisk V3 Scroll Wheel Assembly Replacement, Scroll Wheel Assembly: 步骤 6 中的图像 3，3

Use the flat end of the spudger to pop-out the scroll wheel assembly.
Make sure you are careful when removing the scroll wheel since it is still connected to the device with a ribbon cable. If you pull too hard the cable could break.

编辑

步骤 7

Razer Basilisk V3 Scroll Wheel Assembly Replacement: 步骤 7 中的图像 3，3

Pull up on the top half of the cable connector and pull the cable from the connector.
The connection pins on the wire face towards the scroll wheel assembly housing. When reassembling, make sure the connectors on the cable are facing the correct direction.

编辑