修复你的物品 社区 商店

RCA Voyager II RCT6773W22 Disassembly

简介

Taking apart the RCA Voyager II is pretty straightforward. Here is a short Guide.

Note that the tablet pictured has been disassembled and reassembled before.

你所需要的

  1. RCA Voyager II RCT6773W22 Disassembly, RCA Voyager II RCT6773W22 Disassembly: 步骤 1 中的图像 1，1

    • Have Workstation Prepped

    编辑

  2. RCA Voyager II RCT6773W22 Disassembly: 步骤 2 中的图像 1，1

    • remove the two screws on the top of the device with a PH000 screwdriver

    编辑

  3. RCA Voyager II RCT6773W22 Disassembly: 步骤 3 中的图像 1，1

    • Starting from the top, place pick or plastic tool between the power button and screen edge and push apart slightly.

    编辑

  4. RCA Voyager II RCT6773W22 Disassembly: 步骤 4 中的图像 1，1

    • Run pick across the top to the right and then down the right side and around the rest of the tablet.

    • There is a good amount of space between the bezel and the board. Be gentle, but the risk of breaking components is low.

    编辑

  5. RCA Voyager II RCT6773W22 Disassembly: 步骤 5 中的图像 1，2 RCA Voyager II RCT6773W22 Disassembly: 步骤 5 中的图像 2，2

    • lift section out of the black casing from the bottom, lift and remove by pulling away from tablet.

    编辑

  6. RCA Voyager II RCT6773W22 Disassembly: 步骤 6 中的图像 1，1

    • Battery connection (on older models, may be soldered to board)

    • Front Camera

    • Digitizer

    • LCD

    • Speaker

    编辑

  8. RCA Voyager II RCT6773W22 Disassembly: 步骤 7 中的图像 1，1

    • Remove battery Connection First

    • Do not use any metal tools while the battery is plugged in. It may cause a short.

    编辑

  9. RCA Voyager II RCT6773W22 Disassembly: 步骤 8 中的图像 1，1

    • unplug the speaker

    编辑

  10. RCA Voyager II RCT6773W22 Disassembly: 步骤 9 中的图像 1，3 RCA Voyager II RCT6773W22 Disassembly: 步骤 9 中的图像 2，3 RCA Voyager II RCT6773W22 Disassembly: 步骤 9 中的图像 3，3

    • Lift the black cover over all three flex cables (Camera, LCD, Digitizer) with a plastic tool.

    • The covers are incredibly fragile, and easy to break

    • gently disconnect all three cables with your fingers by pulling slightly

    编辑

  11. RCA Voyager II RCT6773W22 Disassembly: 步骤 10 中的图像 1，1

    • remove the three screws securing the board with your PH000 Screwdriver

    编辑

  12. RCA Voyager II RCT6773W22 Disassembly: 步骤 11 中的图像 1，2 RCA Voyager II RCT6773W22 Disassembly: 步骤 11 中的图像 2，2

    • lift the board out gently

    • Do not tug the board out too hard, the antenna cable on the left is soldered in!

    • Fold board over the left side of the tablet and gently remove tape securing antenna to the case. Use a small amount of heat if necessary.

    编辑

  13. RCA Voyager II RCT6773W22 Disassembly: 步骤 12 中的图像 1，2 RCA Voyager II RCT6773W22 Disassembly: 步骤 12 中的图像 2，2

    • remove tape from top and bottom of the battery.

    • with a plastic piece, lift battery from adhesive securing it in place.

    • do not use a metal or sharp tool to remove the battery, tearing or puncturing it may cause it to explode or heat rapidly, and may damage your device.

    • The battery is secured directly to the back of the LCD. Exercise caution while removing the battery not to damage the LCD.

    • The battery is soft and somewhat malleable - it can bend slightly without damage.

    编辑

  14. RCA Voyager II RCT6773W22 Disassembly: 步骤 13 中的图像 1，2 RCA Voyager II RCT6773W22 Disassembly: 步骤 13 中的图像 2，2

    • Place picks between the lcd and the plastic clips holding it in place.

    • The pick placement to the top left side (near the power button) is smaller and on a corner. I recommend inserting this pick last.

    编辑

  15. RCA Voyager II RCT6773W22 Disassembly: 步骤 14 中的图像 1，1

    • Gently push top right pick down to lift LCD from the clip. Run across the top and right side to further lift LCD.

    • Use picks as needed to separate LCD in other areas.

    编辑

  16. RCA Voyager II RCT6773W22 Disassembly: 步骤 15 中的图像 1，1

    • Once separated and loose, remove picks so you do not damage the LCD while removing it.

    • To remove, lift top of LCD and pull out of case away from the speaker, which is fixed to the digitizer frame.

    编辑

  17. RCA Voyager II RCT6773W22 Disassembly: 步骤 16 中的图像 1，2 RCA Voyager II RCT6773W22 Disassembly: 步骤 16 中的图像 2，2

    • to remove Digitizer/Glass from the frame and speaker, slide a pick under a corner between the glass and frame to loosen adhesive

    • If you're having issues loosening the adhesive, use a heat gun around the edges, then try again.

    编辑

  18. RCA Voyager II RCT6773W22 Disassembly: 步骤 17 中的图像 1，1

    • You have completely dismantled the RCA Voyager II

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

35等其他人完成本指南。

作者

与2其他贡献者

Chris

于01/11/16注册

2,025 声望

撰写一个指南

徽章: 13

+ 10更多徽章

31条评论

what is that flat part that has the little copper bar in the middle. What do you call that?

TheUnchanted Sword - 回复

The LCD has a piece of copper tape on it, is that what you mean?

Sam Goldheart -

Nice Guide. Very Simple and Easy to follow!

Aerial L - 回复

Bonne site merci pour tous je suis très heureux content que entrer dans ce site

diego jamal - 回复

Anyone know which company made this very fragile digitizer for RCA Voyager?

Spock Chen - 回复

添加评论

浏览统计数据:

过去 24 小时： 4

过去 7 天： 15

过去 30 天： 32

总计 21,580