跳转到主内容

简介

The Power Mac G4 MDD Uses a removable cage supporting up to two IDE SuperDrives.

配件

没有特定配件。

  1. The Power Mac G4 MDD: the last, and the fastest G4-based Mac.  This computer boasted up to a Dual 1.42GHz PowerPC G4 CPU (though I have a single 1.25GHz). Six USB ports.
    • The Power Mac G4 MDD: the last, and the fastest G4-based Mac. This computer boasted up to a Dual 1.42GHz PowerPC G4 CPU (though I have a single 1.25GHz).

    • Six USB ports.

    • Four FireWire ports.

    • Assorted SCSI (SCSI50/SCSI68)

    • Assorted Audio

    • Video (ADC & DVI)

    • Networking (RJ-45 Ethernet/56k Modem)

    • Some later model MDD's (such as the dual 1.42GHz) Have a FireWire 800 Port Here:

  2. Unplug the computer. Unplug the power supply and all external connections from the computer. Pull on the side lever and lower the side of the case.
    • Unplug the computer.

    • Unplug the power supply and all external connections from the computer.

    • Pull on the side lever and lower the side of the case.

  3. The hard drive cages are located here.
    • The hard drive cages are located here.

  4. Cage 1 Start by removing this screw. Remove the ATA-66/ IDE ribbon cable from the motherboard.
    • Cage 1

    • Start by removing this screw.

    • Remove the ATA-66/ IDE ribbon cable from the motherboard.

  5. Now, remove the power connection from the drives. Now, remove the power connection from the drives.
    • Now, remove the power connection from the drives.

  6. Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now

    Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now
  7. Push this tab down, and pull the cage toward you. Now, you can set cage 1 aside. Now, you can set cage 1 aside.
    • Push this tab down, and pull the cage toward you.

    • Now, you can set cage 1 aside.

  8. Cage 2: Remove this Phillips screw:
    • Cage 2:

    • Remove this Phillips screw:

    • Disconnect this IDE ribbon cable from the logic board.

  9. It's likely that there is a cable clip holding the ribbon cable to the case. To remove it, push the end, and it should pop up.
    • It's likely that there is a cable clip holding the ribbon cable to the case.

    • To remove it, push the end, and it should pop up.

  10. With the ribbon cable clip free, pull this tab towards you, slide the cage up until it hits the platform under the power supply, and pull it away. Now, set the cage on top of the CPU, and remove the power connectors. Now, set the cage on top of the CPU, and remove the power connectors.
    • With the ribbon cable clip free, pull this tab towards you, slide the cage up until it hits the platform under the power supply, and pull it away.

    • Now, set the cage on top of the CPU, and remove the power connectors.

  11. Once the cables are free, set the drive cage aside. To remove the hard drives from the cages, remove the four screws on the sides of the cage that are connected to the drives, then slide the drives out.
    • Once the cables are free, set the drive cage aside.

    • To remove the hard drives from the cages, remove the four screws on the sides of the cage that are connected to the drives, then slide the drives out.

    • The two cages are cross compatible and can be put in either location.

    • The MDD does not have a 128GB drive limit like older Macs. My MDD has 3 drives (a 400GB Hitatchi Deskstar, 40GB Seagate Barracuda 7200.7, and a 30GB Quantum Fireball LCT).

    • Note the ID jumpers on the two drive set. One is set to Master, the other to slave. A single drive can be set to Cable Select.

  12. Start removing the optical drive cage by removing its back cover. Start removing the optical drive cage by removing its back cover.
    • Start removing the optical drive cage by removing its back cover.

  13. Now, remove the IDE and power cables from the drives. Now, remove the IDE and power cables from the drives. Now, remove the IDE and power cables from the drives.
    • Now, remove the IDE and power cables from the drives.

  14. Remove these two Phillips screws: Pull the cage away from the front until it is free. Slide the cage towards you, and out of the Mac.
    • Remove these two Phillips screws:

    • Pull the cage away from the front until it is free.

    • Slide the cage towards you, and out of the Mac.

  15. To remove the drive(s) from the cage, remove the two screws on each side of the drive(s), then pull the drive out of the cage. My MDD has a 3rd party 22X SuperDrive, for burning DVD's in Leopard (Thank You Generic Drive Support!)
    • To remove the drive(s) from the cage, remove the two screws on each side of the drive(s), then pull the drive out of the cage.

    • My MDD has a 3rd party 22X SuperDrive, for burning DVD's in Leopard (Thank You Generic Drive Support!)

结论

To reassemble your device, follow these instructions in reverse order.

15等其他人完成本指南。

Chris Green

于2009年10月11日注册

33,358 信誉积分

创作了45篇指南

团队

Master Techs Master Techs 的会员

Community

287 名成员

创作了819篇指南

In the Sacramento FATP factory we used to call this the 'media can' in previous models because there were other drives such as ZIP and JAZZ drives available, until this and the one just prior which only had optical drive options, so it became the 'optical cage'

joey - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 17

总计 11,199