跳转到主内容

你所需要的

这个拆解是不是维修指南。 要维修你的的Power Mac G4 M5183,请使用我们的维修手册

  1. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 1 中的图像 1,2 : 步骤 1 中的图像 2,2
    • Pull the tab to open the case.

  2. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 2 中的图像 1,2 : 步骤 2 中的图像 2,2
    • Pull the white tabs down

    • Lift up the RAM

    • Repeat x4

  3. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 3 中的图像 1,2 : 步骤 3 中的图像 2,2
    • Use a flat head screwdriver or spudger to lift up the tabs that hold down the heat-sink.

    • Repeat x2

    • The heat-sink should just lift right off.

  4. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 4 中的图像 1,2 : 步骤 4 中的图像 2,2
    • Remove highlighted screw.

    • The GPU should lift right out.

  5. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 5 中的图像 1,3 : 步骤 5 中的图像 2,3 : 步骤 5 中的图像 3,3
    • Remove highlighted cables.

    • Remove highlighted screws.

    • Lift out the motherboard. (Note: pull to the left to clear the ports from the case)

  6. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 6 中的图像 1,2 : 步骤 6 中的图像 2,2
    • Remove highlighted screws.

    • After removing the screws, simply lift off the CPU from the connector. Use only a minimal amount of pressure when pulling the CPU from the connector.

    • This is the connector after removal of the CPU.

  7. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 7 中的图像 1,3 : 步骤 7 中的图像 2,3 : 步骤 7 中的图像 3,3
    • Remove the face plate. You are supposed to press down the highlighted tabs from the inside.

    • Remove highlighted screws.

    • Slide out the drive. (MAKE SURE TO UNHOOK THE CABLES)

  8. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 8 中的图像 1,3 : 步骤 8 中的图像 2,3 : 步骤 8 中的图像 3,3
    • Remove the highlighted cables.

    • Remove highlighted screw.

    • Lift out the hard drive.

  9. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 9 中的图像 1,2 : 步骤 9 中的图像 2,2
    • Remove highlighted screw. ( SAME SCREW ON OPPOSITE SIDE, REMOVE THAT AS WELL.)

    • Disconnect the connector.

    • After that, just pull it out.

  10. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 10 中的图像 1,3 : 步骤 10 中的图像 2,3 : 步骤 10 中的图像 3,3
    • Use a 2.5 mm hex key to remove these screws.

    • Remove highlighted screw.

    • Feed the wires through the highlighted hole, then pull out the power supply.

  11. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 11 中的图像 1,1
    • You will be left with an empty case.

Harrison Case

于11/06/16注册

128 声望

撰写一个指南

4条评论

Just a little tip.

APPLE tend to use screw connections as a means of ground continuity.

That is - if the CPU card is not screwed down - it might not power on.

Mal - 回复

The is a kit from thelaserhive.com to allow an mATX board to be used inside the G4 cases.

Pete Karnowski - 回复

添加评论

浏览统计数据:

过去 24 小时: 2

过去 7 天: 10

过去 30 天: 44

总计 3,328